patch-2.1.71 linux/drivers/net/hamradio/baycom_ser_hdx.c

Next file: linux/drivers/net/hamradio/bpqether.c
Previous file: linux/drivers/net/hamradio/baycom_ser_fdx.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.1.70/linux/drivers/net/hamradio/baycom_ser_hdx.c linux/drivers/net/hamradio/baycom_ser_hdx.c
@@ -0,0 +1,792 @@
+/*****************************************************************************/
+
+/*
+ *	baycom_ser_hdx.c  -- baycom ser12 halfduplex radio modem driver.
+ *
+ *	Copyright (C) 1997  Thomas Sailer (sailer@ife.ee.ethz.ch)
+ *
+ *	This program is free software; you can redistribute it and/or modify
+ *	it under the terms of the GNU General Public License as published by
+ *	the Free Software Foundation; either version 2 of the License, or
+ *	(at your option) any later version.
+ *
+ *	This program is distributed in the hope that it will be useful,
+ *	but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *	GNU General Public License for more details.
+ *
+ *	You should have received a copy of the GNU General Public License
+ *	along with this program; if not, write to the Free Software
+ *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *  Please note that the GPL allows you to use the driver, NOT the radio.
+ *  In order to use the radio, you need a license from the communications
+ *  authority of your country.
+ *
+ *
+ *  Supported modems
+ *
+ *  ser12:  This is a very simple 1200 baud AFSK modem. The modem consists only
+ *          of a modulator/demodulator chip, usually a TI TCM3105. The computer
+ *          is responsible for regenerating the receiver bit clock, as well as
+ *          for handling the HDLC protocol. The modem connects to a serial port,
+ *          hence the name. Since the serial port is not used as an async serial
+ *          port, the kernel driver for serial ports cannot be used, and this
+ *          driver only supports standard serial hardware (8250, 16450, 16550A)
+ *
+ *
+ *  Command line options (insmod command line)
+ *
+ *  mode     * enables software DCD.
+ *  iobase   base address of the port; common values are 0x3f8, 0x2f8, 0x3e8, 0x2e8
+ *  irq      interrupt line of the port; common values are 4,3
+ *
+ *
+ *  History:
+ *   0.1  26.06.96  Adapted from baycom.c and made network driver interface
+ *        18.10.96  Changed to new user space access routines (copy_{to,from}_user)
+ *   0.3  26.04.97  init code/data tagged
+ *   0.4  08.07.97  alternative ser12 decoding algorithm (uses delta CTS ints)
+ *   0.5  11.11.97  ser12/par96 split into separate files
+ */
+
+/*****************************************************************************/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/types.h>
+#include <linux/fcntl.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/in.h>
+#include <linux/string.h>
+#include <asm/system.h>
+#include <asm/bitops.h>
+#include <asm/io.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/netdevice.h>
+#include <linux/hdlcdrv.h>
+#include <linux/baycom.h>
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * currently this module is supposed to support both module styles, i.e.
+ * the old one present up to about 2.1.9, and the new one functioning
+ * starting with 2.1.21. The reason is I have a kit allowing to compile
+ * this module also under 2.0.x which was requested by several people.
+ * This will go in 2.2
+ */
+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE >= 0x20100
+#include <asm/uaccess.h>
+#else
+#include <asm/segment.h>
+#include <linux/mm.h>
+
+#undef put_user
+#undef get_user
+
+#define put_user(x,ptr) ({ __put_user((unsigned long)(x),(ptr),sizeof(*(ptr))); 0; })
+#define get_user(x,ptr) ({ x = ((__typeof__(*(ptr)))__get_user((ptr),sizeof(*(ptr)))); 0; })
+
+extern inline int copy_from_user(void *to, const void *from, unsigned long n)
+{
+        int i = verify_area(VERIFY_READ, from, n);
+        if (i)
+                return i;
+        memcpy_fromfs(to, from, n);
+        return 0;
+}
+
+extern inline int copy_to_user(void *to, const void *from, unsigned long n)
+{
+        int i = verify_area(VERIFY_WRITE, to, n);
+        if (i)
+                return i;
+        memcpy_tofs(to, from, n);
+        return 0;
+}
+#endif
+
+#if LINUX_VERSION_CODE >= 0x20123
+#include <linux/init.h>
+#else
+#define __init
+#define __initdata
+#define __initfunc(x) x
+#endif
+
+/* --------------------------------------------------------------------- */
+
+#define BAYCOM_DEBUG
+
+/*
+ * modem options; bit mask
+ */
+#define BAYCOM_OPTIONS_SOFTDCD  1
+
+/* --------------------------------------------------------------------- */
+
+static const char bc_drvname[] = "baycom_ser_hdx";
+static const char bc_drvinfo[] = KERN_INFO "baycom_ser_hdx: (C) 1997 Thomas Sailer, HB9JNX/AE4WA\n"
+KERN_INFO "baycom_ser_hdx: version 0.5 compiled " __TIME__ " " __DATE__ "\n";
+
+/* --------------------------------------------------------------------- */
+
+#define NR_PORTS 4
+
+static struct device baycom_device[NR_PORTS];
+
+static struct {
+	char *mode;
+	int iobase, irq;
+} baycom_ports[NR_PORTS] = { { NULL, 0, 0 }, };
+
+/* --------------------------------------------------------------------- */
+
+#define RBR(iobase) (iobase+0)
+#define THR(iobase) (iobase+0)
+#define IER(iobase) (iobase+1)
+#define IIR(iobase) (iobase+2)
+#define FCR(iobase) (iobase+2)
+#define LCR(iobase) (iobase+3)
+#define MCR(iobase) (iobase+4)
+#define LSR(iobase) (iobase+5)
+#define MSR(iobase) (iobase+6)
+#define SCR(iobase) (iobase+7)
+#define DLL(iobase) (iobase+0)
+#define DLM(iobase) (iobase+1)
+
+#define SER12_EXTENT 8
+
+/* ---------------------------------------------------------------------- */
+/*
+ * Information that need to be kept for each board.
+ */
+
+struct baycom_state {
+	struct hdlcdrv_state hdrv;
+
+	unsigned int options;
+
+	struct modem_state {
+		short arb_divider;
+		unsigned char flags;
+		unsigned int shreg;
+		struct modem_state_ser12 {
+			unsigned char tx_bit;
+			int dcd_sum0, dcd_sum1, dcd_sum2;
+			unsigned char last_sample;
+			unsigned char last_rxbit;
+			unsigned int dcd_shreg;
+			unsigned int dcd_time;
+			unsigned int bit_pll;
+			unsigned char interm_sample;
+		} ser12;
+	} modem;
+
+#ifdef BAYCOM_DEBUG
+	struct debug_vals {
+		unsigned long last_jiffies;
+		unsigned cur_intcnt;
+		unsigned last_intcnt;
+		int cur_pllcorr;
+		int last_pllcorr;
+	} debug_vals;
+#endif /* BAYCOM_DEBUG */
+};
+
+/* --------------------------------------------------------------------- */
+
+#define min(a, b) (((a) < (b)) ? (a) : (b))
+#define max(a, b) (((a) > (b)) ? (a) : (b))
+
+/* --------------------------------------------------------------------- */
+
+static void inline baycom_int_freq(struct baycom_state *bc)
+{
+#ifdef BAYCOM_DEBUG
+	unsigned long cur_jiffies = jiffies;
+	/*
+	 * measure the interrupt frequency
+	 */
+	bc->debug_vals.cur_intcnt++;
+	if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) {
+		bc->debug_vals.last_jiffies = cur_jiffies;
+		bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
+		bc->debug_vals.cur_intcnt = 0;
+		bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr;
+		bc->debug_vals.cur_pllcorr = 0;
+	}
+#endif /* BAYCOM_DEBUG */
+}
+
+/* --------------------------------------------------------------------- */
+/*
+ * ===================== SER12 specific routines =========================
+ */
+
+static void inline ser12_set_divisor(struct device *dev,
+				     unsigned char divisor)
+{
+	outb(0x81, LCR(dev->base_addr));	/* DLAB = 1 */
+	outb(divisor, DLL(dev->base_addr));
+	outb(0, DLM(dev->base_addr));
+	outb(0x01, LCR(dev->base_addr));	/* word length = 6 */
+	/*
+	 * make sure the next interrupt is generated;
+	 * 0 must be used to power the modem; the modem draws its
+	 * power from the TxD line
+	 */
+	outb(0x00, THR(dev->base_addr));
+	/*
+	 * it is important not to set the divider while transmitting;
+	 * this reportedly makes some UARTs generating interrupts
+	 * in the hundredthousands per second region
+	 * Reported by: Ignacio.Arenaza@studi.epfl.ch (Ignacio Arenaza Nuno)
+	 */
+}
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * must call the TX arbitrator every 10ms
+ */
+#define SER12_ARB_DIVIDER(bc) ((bc->options & BAYCOM_OPTIONS_SOFTDCD) ? \
+			       36 : 24)
+#define SER12_DCD_INTERVAL(bc) ((bc->options & BAYCOM_OPTIONS_SOFTDCD) ? \
+				240 : 12)
+
+static inline void ser12_tx(struct device *dev, struct baycom_state *bc)
+{
+	/* one interrupt per channel bit */
+	ser12_set_divisor(dev, 12);
+	/*
+	 * first output the last bit (!) then call HDLC transmitter,
+	 * since this may take quite long
+	 */
+	outb(0x0e | (!!bc->modem.ser12.tx_bit), MCR(dev->base_addr));
+	if (bc->modem.shreg <= 1)
+		bc->modem.shreg = 0x10000 | hdlcdrv_getbits(&bc->hdrv);
+	bc->modem.ser12.tx_bit = !(bc->modem.ser12.tx_bit ^
+				   (bc->modem.shreg & 1));
+	bc->modem.shreg >>= 1;
+}
+
+/* --------------------------------------------------------------------- */
+
+static inline void ser12_rx(struct device *dev, struct baycom_state *bc)
+{
+	unsigned char cur_s;
+	/*
+	 * do demodulator
+	 */
+	cur_s = inb(MSR(dev->base_addr)) & 0x10;	/* the CTS line */
+	hdlcdrv_channelbit(&bc->hdrv, cur_s);
+	bc->modem.ser12.dcd_shreg = (bc->modem.ser12.dcd_shreg << 1) |
+		(cur_s != bc->modem.ser12.last_sample);
+	bc->modem.ser12.last_sample = cur_s;
+	if(bc->modem.ser12.dcd_shreg & 1) {
+		if (bc->options & BAYCOM_OPTIONS_SOFTDCD) {
+			unsigned int dcdspos, dcdsneg;
+
+			dcdspos = dcdsneg = 0;
+			dcdspos += ((bc->modem.ser12.dcd_shreg >> 1) & 1);
+			if (!(bc->modem.ser12.dcd_shreg & 0x7ffffffe))
+				dcdspos += 2;
+			dcdsneg += ((bc->modem.ser12.dcd_shreg >> 2) & 1);
+			dcdsneg += ((bc->modem.ser12.dcd_shreg >> 3) & 1);
+			dcdsneg += ((bc->modem.ser12.dcd_shreg >> 4) & 1);
+
+			bc->modem.ser12.dcd_sum0 += 16*dcdspos - dcdsneg;
+		} else
+			bc->modem.ser12.dcd_sum0--;
+	}
+	if(!bc->modem.ser12.dcd_time) {
+		hdlcdrv_setdcd(&bc->hdrv, (bc->modem.ser12.dcd_sum0 +
+					   bc->modem.ser12.dcd_sum1 +
+					   bc->modem.ser12.dcd_sum2) < 0);
+		bc->modem.ser12.dcd_sum2 = bc->modem.ser12.dcd_sum1;
+		bc->modem.ser12.dcd_sum1 = bc->modem.ser12.dcd_sum0;
+		/* offset to ensure DCD off on silent input */
+		bc->modem.ser12.dcd_sum0 = 2;
+		bc->modem.ser12.dcd_time = SER12_DCD_INTERVAL(bc);
+	}
+	bc->modem.ser12.dcd_time--;
+	if (bc->options & BAYCOM_OPTIONS_SOFTDCD) {
+		/*
+		 * PLL code for the improved software DCD algorithm
+		 */
+		if (bc->modem.ser12.interm_sample) {
+			/*
+			 * intermediate sample; set timing correction to normal
+			 */
+			ser12_set_divisor(dev, 4);
+		} else {
+			/*
+			 * do PLL correction and call HDLC receiver
+			 */
+			switch (bc->modem.ser12.dcd_shreg & 7) {
+			case 1: /* transition too late */
+				ser12_set_divisor(dev, 5);
+#ifdef BAYCOM_DEBUG
+				bc->debug_vals.cur_pllcorr++;
+#endif /* BAYCOM_DEBUG */
+				break;
+			case 4:	/* transition too early */
+				ser12_set_divisor(dev, 3);
+#ifdef BAYCOM_DEBUG
+				bc->debug_vals.cur_pllcorr--;
+#endif /* BAYCOM_DEBUG */
+				break;
+			default:
+				ser12_set_divisor(dev, 4);
+				break;
+			}
+			bc->modem.shreg >>= 1;
+			if (bc->modem.ser12.last_sample ==
+			    bc->modem.ser12.last_rxbit)
+				bc->modem.shreg |= 0x10000;
+			bc->modem.ser12.last_rxbit =
+				bc->modem.ser12.last_sample;
+		}
+		if (++bc->modem.ser12.interm_sample >= 3)
+			bc->modem.ser12.interm_sample = 0;
+		/*
+		 * DCD stuff
+		 */
+		if (bc->modem.ser12.dcd_shreg & 1) {
+			unsigned int dcdspos, dcdsneg;
+
+			dcdspos = dcdsneg = 0;
+			dcdspos += ((bc->modem.ser12.dcd_shreg >> 1) & 1);
+			dcdspos += (!(bc->modem.ser12.dcd_shreg & 0x7ffffffe))
+				<< 1;
+			dcdsneg += ((bc->modem.ser12.dcd_shreg >> 2) & 1);
+			dcdsneg += ((bc->modem.ser12.dcd_shreg >> 3) & 1);
+			dcdsneg += ((bc->modem.ser12.dcd_shreg >> 4) & 1);
+
+			bc->modem.ser12.dcd_sum0 += 16*dcdspos - dcdsneg;
+		}
+	} else {
+		/*
+		 * PLL algorithm for the hardware squelch DCD algorithm
+		 */
+		if (bc->modem.ser12.interm_sample) {
+			/*
+			 * intermediate sample; set timing correction to normal
+			 */
+			ser12_set_divisor(dev, 6);
+		} else {
+			/*
+			 * do PLL correction and call HDLC receiver
+			 */
+			switch (bc->modem.ser12.dcd_shreg & 3) {
+			case 1: /* transition too late */
+				ser12_set_divisor(dev, 7);
+#ifdef BAYCOM_DEBUG
+				bc->debug_vals.cur_pllcorr++;
+#endif /* BAYCOM_DEBUG */
+				break;
+			case 2:	/* transition too early */
+				ser12_set_divisor(dev, 5);
+#ifdef BAYCOM_DEBUG
+				bc->debug_vals.cur_pllcorr--;
+#endif /* BAYCOM_DEBUG */
+				break;
+			default:
+				ser12_set_divisor(dev, 6);
+				break;
+			}
+			bc->modem.shreg >>= 1;
+			if (bc->modem.ser12.last_sample ==
+			    bc->modem.ser12.last_rxbit)
+				bc->modem.shreg |= 0x10000;
+			bc->modem.ser12.last_rxbit =
+				bc->modem.ser12.last_sample;
+		}
+		bc->modem.ser12.interm_sample = !bc->modem.ser12.interm_sample;
+		/*
+		 * DCD stuff
+		 */
+		bc->modem.ser12.dcd_sum0 -= (bc->modem.ser12.dcd_shreg & 1);
+	}
+	outb(0x0d, MCR(dev->base_addr));		/* transmitter off */
+	if (bc->modem.shreg & 1) {
+		hdlcdrv_putbits(&bc->hdrv, bc->modem.shreg >> 1);
+		bc->modem.shreg = 0x10000;
+	}
+	if(!bc->modem.ser12.dcd_time) {
+		hdlcdrv_setdcd(&bc->hdrv, (bc->modem.ser12.dcd_sum0 +
+					   bc->modem.ser12.dcd_sum1 +
+					   bc->modem.ser12.dcd_sum2) < 0);
+		bc->modem.ser12.dcd_sum2 = bc->modem.ser12.dcd_sum1;
+		bc->modem.ser12.dcd_sum1 = bc->modem.ser12.dcd_sum0;
+		/* offset to ensure DCD off on silent input */
+		bc->modem.ser12.dcd_sum0 = 2;
+		bc->modem.ser12.dcd_time = SER12_DCD_INTERVAL(bc);
+	}
+	bc->modem.ser12.dcd_time--;
+}
+
+/* --------------------------------------------------------------------- */
+
+static void ser12_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct device *dev = (struct device *)dev_id;
+	struct baycom_state *bc = (struct baycom_state *)dev->priv;
+
+	if (!dev || !bc || bc->hdrv.magic != HDLCDRV_MAGIC)
+		return;
+
+	baycom_int_freq(bc);
+	/*
+	 * check if transmitter active
+	 */
+	if (hdlcdrv_ptt(&bc->hdrv))
+		ser12_tx(dev, bc);
+	else {
+		ser12_rx(dev, bc);
+		if (--bc->modem.arb_divider <= 0) {
+			bc->modem.arb_divider = SER12_ARB_DIVIDER(bc);
+			sti();
+			hdlcdrv_arbitrate(dev, &bc->hdrv);
+		}
+	}
+	sti();
+	hdlcdrv_transmitter(dev, &bc->hdrv);
+	hdlcdrv_receiver(dev, &bc->hdrv);
+}
+
+/* --------------------------------------------------------------------- */
+
+enum uart { c_uart_unknown, c_uart_8250,
+	    c_uart_16450, c_uart_16550, c_uart_16550A};
+static const char *uart_str[] = { 
+	"unknown", "8250", "16450", "16550", "16550A" 
+};
+
+static enum uart ser12_check_uart(unsigned int iobase)
+{
+	unsigned char b1,b2,b3;
+	enum uart u;
+	enum uart uart_tab[] =
+		{ c_uart_16450, c_uart_unknown, c_uart_16550, c_uart_16550A };
+
+	b1 = inb(MCR(iobase));
+	outb(b1 | 0x10, MCR(iobase));	/* loopback mode */
+	b2 = inb(MSR(iobase));
+	outb(0x1a, MCR(iobase));
+	b3 = inb(MSR(iobase)) & 0xf0;
+	outb(b1, MCR(iobase));			/* restore old values */
+	outb(b2, MSR(iobase));
+	if (b3 != 0x90)
+		return c_uart_unknown;
+	inb(RBR(iobase));
+	inb(RBR(iobase));
+	outb(0x01, FCR(iobase));		/* enable FIFOs */
+	u = uart_tab[(inb(IIR(iobase)) >> 6) & 3];
+	if (u == c_uart_16450) {
+		outb(0x5a, SCR(iobase));
+		b1 = inb(SCR(iobase));
+		outb(0xa5, SCR(iobase));
+		b2 = inb(SCR(iobase));
+		if ((b1 != 0x5a) || (b2 != 0xa5))
+			u = c_uart_8250;
+	}
+	return u;
+}
+
+/* --------------------------------------------------------------------- */
+
+static int ser12_open(struct device *dev)
+{
+	struct baycom_state *bc = (struct baycom_state *)dev->priv;
+	enum uart u;
+
+	if (!dev || !bc)
+		return -ENXIO;
+	if (!dev->base_addr || dev->base_addr > 0x1000-SER12_EXTENT ||
+	    dev->irq < 2 || dev->irq > 15)
+		return -ENXIO;
+	if (check_region(dev->base_addr, SER12_EXTENT))
+		return -EACCES;
+	memset(&bc->modem, 0, sizeof(bc->modem));
+	bc->hdrv.par.bitrate = 1200;
+	if ((u = ser12_check_uart(dev->base_addr)) == c_uart_unknown)
+		return -EIO;
+	outb(0, FCR(dev->base_addr));  /* disable FIFOs */
+	outb(0x0d, MCR(dev->base_addr));
+	outb(0x0d, MCR(dev->base_addr));
+	outb(0, IER(dev->base_addr));
+	if (request_irq(dev->irq, ser12_interrupt, SA_INTERRUPT,
+			"baycom_ser12", dev))
+		return -EBUSY;
+	request_region(dev->base_addr, SER12_EXTENT, "baycom_ser12");
+	/*
+	 * enable transmitter empty interrupt
+	 */
+	outb(2, IER(dev->base_addr));
+	/*
+	 * set the SIO to 6 Bits/character and 19200 or 28800 baud, so that
+	 * we get exactly (hopefully) 2 or 3 interrupts per radio symbol,
+	 * depending on the usage of the software DCD routine
+	 */
+	ser12_set_divisor(dev, (bc->options & BAYCOM_OPTIONS_SOFTDCD) ? 4 : 6);
+	printk(KERN_INFO "%s: ser12 at iobase 0x%lx irq %u options "
+	       "0x%x uart %s\n", bc_drvname, dev->base_addr, dev->irq,
+	       bc->options, uart_str[u]);
+	MOD_INC_USE_COUNT;
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+
+static int ser12_close(struct device *dev)
+{
+	struct baycom_state *bc = (struct baycom_state *)dev->priv;
+
+	if (!dev || !bc)
+		return -EINVAL;
+	/*
+	 * disable interrupts
+	 */
+	outb(0, IER(dev->base_addr));
+	outb(1, MCR(dev->base_addr));
+	free_irq(dev->irq, dev);
+	release_region(dev->base_addr, SER12_EXTENT);
+	printk(KERN_INFO "%s: close ser12 at iobase 0x%lx irq %u\n",
+	       bc_drvname, dev->base_addr, dev->irq);
+	MOD_DEC_USE_COUNT;
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+/*
+ * ===================== hdlcdrv driver interface =========================
+ */
+
+/* --------------------------------------------------------------------- */
+
+static int baycom_ioctl(struct device *dev, struct ifreq *ifr,
+			struct hdlcdrv_ioctl *hi, int cmd);
+
+/* --------------------------------------------------------------------- */
+
+static struct hdlcdrv_ops ser12_ops = {
+	bc_drvname,
+	bc_drvinfo,
+	ser12_open,
+	ser12_close,
+	baycom_ioctl
+};
+
+/* --------------------------------------------------------------------- */
+
+static int baycom_setmode(struct baycom_state *bc, const char *modestr)
+{
+	bc->options = !!strchr(modestr, '*');
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+
+static int baycom_ioctl(struct device *dev, struct ifreq *ifr,
+			struct hdlcdrv_ioctl *hi, int cmd)
+{
+	struct baycom_state *bc;
+	struct baycom_ioctl bi;
+	int cmd2;
+
+	if (!dev || !dev->priv ||
+	    ((struct baycom_state *)dev->priv)->hdrv.magic != HDLCDRV_MAGIC) {
+		printk(KERN_ERR "bc_ioctl: invalid device struct\n");
+		return -EINVAL;
+	}
+	bc = (struct baycom_state *)dev->priv;
+
+	if (cmd != SIOCDEVPRIVATE)
+		return -ENOIOCTLCMD;
+	if (get_user(cmd2, (int *)ifr->ifr_data))
+		return -EFAULT;
+	switch (hi->cmd) {
+	default:
+		break;
+
+	case HDLCDRVCTL_GETMODE:
+		strcpy(hi->data.modename, "ser12");
+		if (bc->options & 1)
+			strcat(hi->data.modename, "*");
+		if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
+			return -EFAULT;
+		return 0;
+
+	case HDLCDRVCTL_SETMODE:
+		if (!suser() || dev->start)
+			return -EACCES;
+		hi->data.modename[sizeof(hi->data.modename)-1] = '\0';
+		return baycom_setmode(bc, hi->data.modename);
+
+	case HDLCDRVCTL_MODELIST:
+		strcpy(hi->data.modename, "ser12");
+		if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
+			return -EFAULT;
+		return 0;
+
+	case HDLCDRVCTL_MODEMPARMASK:
+		return HDLCDRV_PARMASK_IOBASE | HDLCDRV_PARMASK_IRQ;
+
+	}
+
+	if (copy_from_user(&bi, ifr->ifr_data, sizeof(bi)))
+		return -EFAULT;
+	switch (bi.cmd) {
+	default:
+		return -ENOIOCTLCMD;
+
+#ifdef BAYCOM_DEBUG
+	case BAYCOMCTL_GETDEBUG:
+		bi.data.dbg.debug1 = bc->hdrv.ptt_keyed;
+		bi.data.dbg.debug2 = bc->debug_vals.last_intcnt;
+		bi.data.dbg.debug3 = bc->debug_vals.last_pllcorr;
+		break;
+#endif /* BAYCOM_DEBUG */
+
+	}
+	if (copy_to_user(ifr->ifr_data, &bi, sizeof(bi)))
+		return -EFAULT;
+	return 0;
+
+}
+
+/* --------------------------------------------------------------------- */
+
+__initfunc(int baycom_ser_hdx_init(void))
+{
+	int i, j, found = 0;
+	char set_hw = 1;
+	struct baycom_state *bc;
+	char ifname[HDLCDRV_IFNAMELEN];
+
+
+	printk(bc_drvinfo);
+	/*
+	 * register net devices
+	 */
+	for (i = 0; i < NR_PORTS; i++) {
+		struct device *dev = baycom_device+i;
+		sprintf(ifname, "bcsh%d", i);
+
+		if (!baycom_ports[i].mode)
+			set_hw = 0;
+		if (!set_hw)
+			baycom_ports[i].iobase = baycom_ports[i].irq = 0;
+		j = hdlcdrv_register_hdlcdrv(dev, &ser12_ops,
+					     sizeof(struct baycom_state),
+					     ifname, baycom_ports[i].iobase,
+					     baycom_ports[i].irq, 0);
+		if (!j) {
+			bc = (struct baycom_state *)dev->priv;
+			if (set_hw && baycom_setmode(bc, baycom_ports[i].mode))
+				set_hw = 0;
+			found++;
+		} else {
+			printk(KERN_WARNING "%s: cannot register net device\n",
+			       bc_drvname);
+		}
+	}
+	if (!found)
+		return -ENXIO;
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+
+#ifdef MODULE
+
+/*
+ * command line settable parameters
+ */
+static char *mode[NR_PORTS] = { "ser12*", };
+static int iobase[NR_PORTS] = { 0x3f8, };
+static int irq[NR_PORTS] = { 4, };
+
+#if LINUX_VERSION_CODE >= 0x20115
+
+MODULE_PARM(mode, "1-" __MODULE_STRING(NR_PORTS) "s");
+MODULE_PARM_DESC(mode, "baycom operating mode; * for software DCD");
+MODULE_PARM(iobase, "1-" __MODULE_STRING(NR_PORTS) "i");
+MODULE_PARM_DESC(iobase, "baycom io base address");
+MODULE_PARM(irq, "1-" __MODULE_STRING(NR_PORTS) "i");
+MODULE_PARM_DESC(irq, "baycom irq number");
+
+MODULE_AUTHOR("Thomas M. Sailer, sailer@ife.ee.ethz.ch, hb9jnx@hb9w.che.eu");
+MODULE_DESCRIPTION("Baycom ser12 half duplex amateur radio modem driver");
+
+#endif
+
+__initfunc(int init_module(void))
+{
+	int i;
+
+	for (i = 0; (i < NR_PORTS) && (mode[i]); i++) {
+		baycom_ports[i].mode = mode[i];
+		baycom_ports[i].iobase = iobase[i];
+		baycom_ports[i].irq = irq[i];
+	}
+	if (i < NR_PORTS-1)
+		baycom_ports[i+1].mode = NULL;
+	return baycom_ser_hdx_init();
+}
+
+/* --------------------------------------------------------------------- */
+
+void cleanup_module(void)
+{
+	int i;
+
+	for(i = 0; i < NR_PORTS; i++) {
+		struct device *dev = baycom_device+i;
+		struct baycom_state *bc = (struct baycom_state *)dev->priv;
+
+		if (bc) {
+			if (bc->hdrv.magic != HDLCDRV_MAGIC)
+				printk(KERN_ERR "baycom: invalid magic in "
+				       "cleanup_module\n");
+			else
+				hdlcdrv_unregister_hdlcdrv(dev);
+		}
+	}
+}
+
+#else /* MODULE */
+/* --------------------------------------------------------------------- */
+/*
+ * format: baycom_ser_=io,irq,mode
+ * mode: [*]
+ * * indicates sofware DCD
+ */
+
+__initfunc(void baycom_ser_hdx_setup(char *str, int *ints))
+{
+	int i;
+
+	for (i = 0; (i < NR_PORTS) && (baycom_ports[i].mode); i++);
+	if ((i >= NR_PORTS) || (ints[0] < 2)) {
+		printk(KERN_INFO "%s: too many or invalid interface "
+		       "specifications\n", bc_drvname);
+		return;
+	}
+	baycom_ports[i].mode = str;
+	baycom_ports[i].iobase = ints[1];
+	baycom_ports[i].irq = ints[2];
+	if (i < NR_PORTS-1)
+		baycom_ports[i+1].mode = NULL;
+}
+
+#endif /* MODULE */
+/* --------------------------------------------------------------------- */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov