patch-2.2.3 linux/drivers/scsi/sym53c416.c

Next file: linux/drivers/scsi/sym53c416.h
Previous file: linux/drivers/scsi/st.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.2.2/linux/drivers/scsi/sym53c416.c linux/drivers/scsi/sym53c416.c
@@ -0,0 +1,806 @@
+/* 
+ *  sym53c416.c
+ *  Low-level SCSI driver for sym53c416 chip.
+ *  Copyright (C) 1998 Lieven Willems (lw_linux@hotmail.com)
+ * 
+ *  LILO command line usage: sym53c416=<PORTBASE>[,<IRQ>]
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2, or (at your option) any
+ *  later version.
+ *
+ *  This program is distributed in the hope that it will be useful, but
+ *  WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ *  General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <asm/dma.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <linux/blk.h>
+#include <linux/version.h>
+#include "scsi.h"
+#include "hosts.h"
+#include "sd.h"
+#include "sym53c416.h"
+
+#define VERSION_STRING        "Version 1.0.0"
+
+#define TC_LOW       0x00     /* Transfer counter low        */
+#define TC_MID       0x01     /* Transfer counter mid        */
+#define SCSI_FIFO    0x02     /* SCSI FIFO register          */
+#define COMMAND_REG  0x03     /* Command Register            */
+#define STATUS_REG   0x04     /* Status Register (READ)      */
+#define DEST_BUS_ID  0x04     /* Destination Bus ID (WRITE)  */
+#define INT_REG      0x05     /* Interrupt Register (READ)   */
+#define TOM          0x05     /* Time out multiplier (WRITE) */
+#define STP          0x06     /* Synchronous Transfer period */
+#define SYNC_OFFSET  0x07     /* Synchronous Offset          */
+#define CONF_REG_1   0x08     /* Configuration register 1    */
+#define CONF_REG_2   0x0B     /* Configuration register 2    */
+#define CONF_REG_3   0x0C     /* Configuration register 3    */
+#define CONF_REG_4   0x0D     /* Configuration register 4    */
+#define TC_HIGH      0x0E     /* Transfer counter high       */
+#define PIO_FIFO_1   0x10     /* PIO FIFO register 1         */
+#define PIO_FIFO_2   0x11     /* PIO FIFO register 2         */
+#define PIO_FIFO_3   0x12     /* PIO FIFO register 3         */
+#define PIO_FIFO_4   0x13     /* PIO FIFO register 4         */
+#define PIO_FIFO_CNT 0x14     /* PIO FIFO count              */
+#define PIO_INT_REG  0x15     /* PIO interrupt register      */
+#define CONF_REG_5   0x16     /* Configuration register 5    */
+#define FEATURE_EN   0x1D     /* Feature Enable register     */
+
+/* Configuration register 1 entries: */
+/* Bits 2-0: SCSI ID of host adapter */
+#define SCM    0x80                     /* Slow Cable Mode              */
+#define SRID   0x40                     /* SCSI Reset Interrupt Disable */
+#define PTM    0x20                     /* Parity Test Mode             */
+#define EPC    0x10                     /* Enable Parity Checking       */
+#define CTME   0x08                     /* Special Test Mode            */
+
+/* Configuration register 2 entries: */
+#define FE     0x40                     /* Features Enable              */
+#define SCSI2  0x08                     /* SCSI 2 Enable                */
+#define TBPA   0x04                     /* Target Bad Parity Abort      */
+
+/* Configuration register 3 entries: */
+#define IDMRC  0x80                     /* ID Message Reserved Check    */
+#define QTE    0x40                     /* Queue Tag Enable             */
+#define CDB10  0x20                     /* Command Descriptor Block 10  */
+#define FSCSI  0x10                     /* FastSCSI                     */
+#define FCLK   0x08                     /* FastClock                    */
+
+/* Configuration register 4 entries: */
+#define RBS    0x08                     /* Register bank select         */
+#define EAN    0x04                     /* Enable Active Negotiation    */
+
+/* Configuration register 5 entries: */
+#define LPSR   0x80                     /* Lower Power SCSI Reset       */
+#define IE     0x20                     /* Interrupt Enable             */
+#define LPM    0x02                     /* Low Power Mode               */
+#define WSE0   0x01                     /* 0WS Enable                   */
+
+/* Interrupt register entries: */
+#define SRST   0x80                     /* SCSI Reset                   */
+#define ILCMD  0x40                     /* Illegal Command              */
+#define DIS    0x20                     /* Disconnect                   */
+#define BS     0x10                     /* Bus Service                  */
+#define FC     0x08                     /* Function Complete            */
+#define RESEL  0x04                     /* Reselected                   */
+#define SI     0x03                     /* Selection Interrupt          */
+
+/* Status Register Entries: */
+#define SCI    0x80                     /* SCSI Core Int                */
+#define GE     0x40                     /* Gross Error                  */
+#define PE     0x20                     /* Parity Error                 */
+#define TC     0x10                     /* Terminal Count               */
+#define VGC    0x08                     /* Valid Group Code             */
+#define PHBITS 0x07                     /* Phase bits                   */
+
+/* PIO Interrupt Register Entries: */
+#define SCI    0x80                     /* SCSI Core Int                */
+#define PFI    0x40                     /* PIO FIFO Interrupt           */
+#define FULL   0x20                     /* PIO FIFO Full                */
+#define EMPTY  0x10                     /* PIO FIFO Empty               */
+#define CE     0x08                     /* Collision Error              */
+#define OUE    0x04                     /* Overflow / Underflow error   */
+#define FIE    0x02                     /* Full Interrupt Enable        */
+#define EIE    0x01                     /* Empty Interrupt Enable       */
+
+/* SYM53C416 SCSI phases (lower 3 bits of SYM53C416_STATUS_REG) */
+#define PHASE_DATA_OUT    0x00
+#define PHASE_DATA_IN     0x01
+#define PHASE_COMMAND     0x02
+#define PHASE_STATUS      0x03
+#define PHASE_RESERVED_1  0x04
+#define PHASE_RESERVED_2  0x05
+#define PHASE_MESSAGE_OUT 0x06
+#define PHASE_MESSAGE_IN  0x07
+
+/* SYM53C416 core commands */
+#define NOOP                      0x00
+#define FLUSH_FIFO                0x01
+#define RESET_CHIP                0x02
+#define RESET_SCSI_BUS            0x03
+#define DISABLE_SEL_RESEL         0x45
+#define RESEL_SEQ                 0x40
+#define SEL_WITHOUT_ATN_SEQ       0x41
+#define SEL_WITH_ATN_SEQ          0x42
+#define SEL_WITH_ATN_AND_STOP_SEQ 0x43
+#define ENABLE_SEL_RESEL          0x44
+#define SEL_WITH_ATN3_SEQ         0x46
+#define RESEL3_SEQ                0x47
+#define SND_MSG                   0x20
+#define SND_STAT                  0x21
+#define SND_DATA                  0x22
+#define DISCONNECT_SEQ            0x23
+#define TERMINATE_SEQ             0x24
+#define TARGET_COMM_COMPLETE_SEQ  0x25
+#define DISCONN                   0x27
+#define RECV_MSG_SEQ              0x28
+#define RECV_CMD                  0x29
+#define RECV_DATA                 0x2A
+#define RECV_CMD_SEQ              0x2B
+#define TARGET_ABORT_PIO          0x04
+#define TRANSFER_INFORMATION      0x10
+#define INIT_COMM_COMPLETE_SEQ    0x11
+#define MSG_ACCEPTED              0x12
+#define TRANSFER_PAD              0x18
+#define SET_ATN                   0x1A
+#define RESET_ATN                 0x1B
+#define ILLEGAL                   0xFF
+
+#define PIO_MODE                  0x80
+
+#define IO_RANGE 0x20         /* 0x00 - 0x1F                   */
+#define ID       "sym53c416"
+#define PIO_SIZE 128          /* Size of PIO fifo is 128 bytes */
+
+#define READ_TIMEOUT              150
+#define WRITE_TIMEOUT             150
+
+#ifdef MODULE
+
+#define sym53c416_base sym53c416
+#define sym53c416_base_1 sym53c416_1
+#define sym53c416_base_2 sym53c416_2
+#define sym53c416_base_3 sym53c416_3
+
+static unsigned short sym53c416_base = 0;
+static unsigned int sym53c416_irq = 0;
+static unsigned short sym53c416_base_1 = 0;
+static unsigned int sym53c416_irq_1 = 0;
+static unsigned short sym53c416_base_2 = 0;
+static unsigned int sym53c416_irq_2 = 0;
+static unsigned short sym53c416_base_3 = 0;
+static unsigned int sym53c416_irq_3 = 0;
+
+#endif
+
+/* #define DEBUG */
+
+/* Macro for debugging purposes */
+
+#ifdef DEBUG
+#define DEB(x) x
+#else
+#define DEB(x)
+#endif
+
+#define MAXHOSTS 4
+
+enum phases
+  {
+  idle,
+  data_out,
+  data_in,
+  command_ph,
+  status_ph,
+  message_out,
+  message_in
+  };
+
+typedef struct
+  {
+  int base;
+  int irq;
+  int scsi_id;
+  } host;
+
+host hosts[MAXHOSTS] = {
+                       {0, 0, SYM53C416_SCSI_ID},
+                       {0, 0, SYM53C416_SCSI_ID},
+                       {0, 0, SYM53C416_SCSI_ID},
+                       {0, 0, SYM53C416_SCSI_ID}
+                       };
+
+static int host_index = 0;
+
+static char info[120];
+
+static Scsi_Cmnd *current_command = NULL;
+
+struct proc_dir_entry proc_scsi_sym53c416 = {PROC_SCSI_SYM53C416, 7, ID, S_IFDIR | S_IRUGO | S_IXUGO, 2};
+
+int fastpio = 1;
+
+int probeaddrs[] = {0x200, 0x220, 0x240, 0};
+
+static void sym53c416_set_transfer_counter(int base, unsigned int len)
+  {
+  /* Program Transfer Counter */
+  outb(len & 0x0000FF, base + TC_LOW);
+  outb((len & 0x00FF00) >> 8, base + TC_MID);
+  outb((len & 0xFF0000) >> 16, base + TC_HIGH);
+  }
+
+/* Returns the number of bytes read */
+static __inline__ unsigned int sym53c416_read(int base, unsigned char *buffer, unsigned int len)
+  {
+  unsigned int orig_len = len;
+  unsigned long flags = 0;
+  unsigned int bytes_left;
+  int i;
+  int timeout = READ_TIMEOUT;
+
+  /* Do transfer */
+  save_flags(flags);
+  cli();
+  while(len && timeout)
+    {
+    bytes_left = inb(base + PIO_FIFO_CNT); /* Number of bytes in the PIO FIFO */
+    if(fastpio && bytes_left > 3)
+      {
+      insl(base + PIO_FIFO_1, buffer, bytes_left >> 2);
+      buffer += bytes_left & 0xFC;
+      len -= bytes_left & 0xFC;
+      }
+    else if(bytes_left > 0)
+      {
+      len -= bytes_left;
+      for(; bytes_left > 0; bytes_left--)
+        *(buffer++) = inb(base + PIO_FIFO_1);
+      }
+    else
+      {
+      i = jiffies + timeout;
+      restore_flags(flags);
+      while(jiffies < i && (inb(base + PIO_INT_REG) & EMPTY) && timeout)
+        if(inb(base + PIO_INT_REG) & SCI)
+          timeout = 0;
+      save_flags(flags);
+      cli();
+      if(inb(base + PIO_INT_REG) & EMPTY)
+        timeout = 0;
+      }
+    }
+  restore_flags(flags);
+  return orig_len - len;
+  }
+
+/* Returns the number of bytes written */
+static __inline__ unsigned int sym53c416_write(int base, unsigned char *buffer, unsigned int len)
+  {
+  unsigned int orig_len = len;
+  unsigned long flags = 0;
+  unsigned int bufferfree;
+  unsigned int i;
+  unsigned int timeout = WRITE_TIMEOUT;
+
+  /* Do transfer */
+  save_flags(flags);
+  cli();
+  while(len && timeout)
+    {
+    bufferfree = PIO_SIZE - inb(base + PIO_FIFO_CNT);
+    if(bufferfree > len)
+      bufferfree = len;
+    if(fastpio && bufferfree > 3)
+      {
+      outsl(base + PIO_FIFO_1, buffer, bufferfree >> 2);
+      buffer += bufferfree & 0xFC;
+      len -= bufferfree & 0xFC;
+      }
+    else if(bufferfree > 0)
+      {
+      len -= bufferfree;
+      for(; bufferfree > 0; bufferfree--)
+        outb(*(buffer++), base + PIO_FIFO_1);
+      }
+    else
+      {
+      i = jiffies + timeout;
+      restore_flags(flags);
+      while(jiffies < i && (inb(base + PIO_INT_REG) & FULL) && timeout)
+        ;
+      save_flags(flags);
+      cli();
+      if(inb(base + PIO_INT_REG) & FULL)
+        timeout = 0;
+      }
+    }
+  restore_flags(flags);
+  return orig_len - len;
+  }
+
+static void sym53c416_intr_handle(int irq, void *dev_id, struct pt_regs *regs)
+  {
+  int base = 0;
+  int i;
+  unsigned long flags = 0;
+  unsigned char status_reg, pio_int_reg, int_reg;
+  struct scatterlist *sglist;
+  unsigned int sgcount;
+  unsigned int tot_trans = 0;
+
+  /* We search the base address of the host adapter which caused the interrupt */
+  for(i = 0; i < host_index && !base; i++)
+    if(irq == hosts[i].irq)
+      base = hosts[i].base;
+  /* If no adapter found, we cannot handle the interrupt. Leave a message */
+  /* and continue. This should never happen...                            */
+  if(!base)
+    {
+    printk("sym53c416: No host adapter defined for interrupt %d\n", irq);
+    return;
+    }
+  /* Now we have the base address and we can start handling the interrupt */
+  save_flags(flags);
+  cli();
+  status_reg = inb(base + STATUS_REG);
+  pio_int_reg = inb(base + PIO_INT_REG);
+  int_reg = inb(base + INT_REG);
+  restore_flags(flags);
+
+  /* First, we handle error conditions */
+  if(int_reg & SCI)         /* SCSI Reset */
+    {
+    printk("sym53c416: Warning: Reset received\n");
+    current_command->SCp.phase = idle;
+    current_command->result = DID_RESET << 16;
+    current_command->scsi_done(current_command);
+    return;
+    }
+  if(int_reg & ILCMD)       /* Illegal Command */
+    {
+    printk("sym53c416: Warning: Illegal Command: 0x%02x\n", inb(base + COMMAND_REG));
+    current_command->SCp.phase = idle;
+    current_command->result = DID_ERROR << 16;
+    current_command->scsi_done(current_command);
+    return;
+    }
+  if(status_reg & GE)         /* Gross Error */
+    {
+    printk("sym53c416: Warning: Gross Error\n");
+    current_command->SCp.phase = idle;
+    current_command->result = DID_ERROR << 16;
+    current_command->scsi_done(current_command);
+    return;
+    }
+  if(status_reg & PE)         /* Parity Error */
+    {
+    printk("sym53c416: Warning: Parity Error\n");
+    current_command->SCp.phase = idle;
+    current_command->result = DID_PARITY << 16;
+    current_command->scsi_done(current_command);
+    return;
+    }
+  if(pio_int_reg & (CE | OUE))
+    {
+    printk("sym53c416: Warning: PIO Interrupt Error\n");
+    current_command->SCp.phase = idle;
+    current_command->result = DID_ERROR << 16;
+    current_command->scsi_done(current_command);
+    return;
+    }
+  if(int_reg & DIS)           /* Disconnect */
+    {
+    if(current_command->SCp.phase != message_in)
+      current_command->result = DID_NO_CONNECT << 16;
+    else
+      current_command->result = (current_command->SCp.Status & 0xFF) | ((current_command->SCp.Message & 0xFF) << 8) | (DID_OK << 16);
+    current_command->SCp.phase = idle;
+    current_command->scsi_done(current_command);
+    return;
+    }
+  /* Now we handle SCSI phases         */
+  switch(status_reg & PHBITS)       /* Filter SCSI phase out of status reg */
+    {
+    case PHASE_DATA_OUT:
+      {
+      if(int_reg & BS)
+        {
+        current_command->SCp.phase = data_out;
+        outb(FLUSH_FIFO, base + COMMAND_REG);
+        sym53c416_set_transfer_counter(base, current_command->request_bufflen);
+        outb(TRANSFER_INFORMATION | PIO_MODE, base + COMMAND_REG);
+        if(!current_command->use_sg)
+          tot_trans = sym53c416_write(base, current_command->request_buffer, current_command->request_bufflen);
+        else
+          {
+          sgcount = current_command->use_sg;
+          sglist = current_command->request_buffer;
+          while(sgcount--)
+            {
+            tot_trans += sym53c416_write(base, sglist->address, sglist->length);
+            sglist++;
+            }
+          }
+        if(tot_trans < current_command->underflow)
+          printk("sym53c416: Warning: underflow, wrote %d bytes, request for %d bytes\n", tot_trans, current_command->underflow);
+        }
+      break;
+      }
+    case PHASE_DATA_IN:
+      {
+      if(int_reg & BS)
+        {
+        current_command->SCp.phase = data_in;
+        outb(FLUSH_FIFO, base + COMMAND_REG);
+        sym53c416_set_transfer_counter(base, current_command->request_bufflen);
+        outb(TRANSFER_INFORMATION | PIO_MODE, base + COMMAND_REG);
+        if(!current_command->use_sg)
+          tot_trans = sym53c416_read(base, current_command->request_buffer, current_command->request_bufflen);
+        else
+          {
+          sgcount = current_command->use_sg;
+          sglist = current_command->request_buffer;
+          while(sgcount--)
+            {
+            tot_trans += sym53c416_read(base, sglist->address, sglist->length);
+            sglist++;
+            }
+          }
+        if(tot_trans < current_command->underflow)
+          printk("sym53c416: Warning: underflow, read %d bytes, request for %d bytes\n", tot_trans, current_command->underflow);
+        }
+      break;
+      }
+    case PHASE_COMMAND:
+      {
+      current_command->SCp.phase = command_ph;
+      printk("sym53c416: Warning: Unknown interrupt in command phase\n");
+      break;
+      }
+    case PHASE_STATUS:
+      {
+      current_command->SCp.phase = status_ph;
+      outb(FLUSH_FIFO, base + COMMAND_REG);
+      outb(INIT_COMM_COMPLETE_SEQ, base + COMMAND_REG);
+      break;
+      }
+    case PHASE_RESERVED_1:
+    case PHASE_RESERVED_2:
+      {
+      printk("sym53c416: Warning: Reserved phase\n");
+      break;
+      }
+    case PHASE_MESSAGE_OUT:
+      {
+      current_command->SCp.phase = message_out;
+      outb(SET_ATN, base + COMMAND_REG);
+      outb(MSG_ACCEPTED, base + COMMAND_REG);
+      break;
+      }
+    case PHASE_MESSAGE_IN:
+      {
+      current_command->SCp.phase = message_in;
+      current_command->SCp.Status = inb(base + SCSI_FIFO);
+      current_command->SCp.Message = inb(base + SCSI_FIFO);
+      if(current_command->SCp.Message == SAVE_POINTERS || current_command->SCp.Message == DISCONNECT)
+        outb(SET_ATN, base + COMMAND_REG);
+      outb(MSG_ACCEPTED, base + COMMAND_REG);
+      break;
+      }
+    }
+  }
+
+static void sym53c416_init(int base, int scsi_id)
+  {
+  outb(RESET_CHIP, base + COMMAND_REG);
+  outb(NOOP, base + COMMAND_REG);
+  outb(0x99, base + TOM); /* Time out of 250 ms */
+  outb(0x05, base + STP);
+  outb(0x00, base + SYNC_OFFSET);
+  outb(EPC | scsi_id, base + CONF_REG_1);
+  outb(FE | SCSI2 | TBPA, base + CONF_REG_2);
+  outb(IDMRC | QTE | CDB10 | FSCSI | FCLK, base + CONF_REG_3);
+  outb(0x83 | EAN, base + CONF_REG_4);
+  outb(IE | WSE0, base + CONF_REG_5);
+  outb(0, base + FEATURE_EN);
+  }
+
+static int sym53c416_probeirq(int base, int scsi_id)
+  {
+  int irq, irqs, i;
+
+  /* Clear interrupt register */
+  inb(base + INT_REG);
+  /* Start probing for irq's */
+  irqs = probe_irq_on();
+  /* Reinit chip */
+  sym53c416_init(base, scsi_id);
+  /* Cause interrupt */
+  outb(NOOP, base + COMMAND_REG);
+  outb(ILLEGAL, base + COMMAND_REG);
+  outb(0x07, base + DEST_BUS_ID);
+  outb(0x00, base + DEST_BUS_ID);
+  /* Wait for interrupt to occur */
+  i = jiffies + 20;
+  while(i > jiffies && !(inb(base + STATUS_REG) & SCI))
+    barrier();
+  if(i <= jiffies) /* timed out */
+    return 0;
+  /* Get occurred irq */
+  irq = probe_irq_off(irqs);
+  sym53c416_init(base, scsi_id);
+  return irq;
+  }
+
+/* Setup: sym53c416=base,irq */
+void sym53c416_setup(char *str, int *ints)
+  {
+  int i;
+
+  if(host_index >= MAXHOSTS)
+    {
+    printk("sym53c416.c: Too many hosts defined\n");
+    }
+  else
+    {
+    if(ints[0] < 1 || ints[0] > 2)
+      {
+      printk("sym53c416.c: Wrong number of parameters:\n");
+      printk("sym53c416.c: usage: sym53c416=<base>[,<irq>]\n");
+      }
+    else
+      {
+      for(i = 0; i < host_index && i >= 0; i++)
+        if(hosts[i].base == ints[1])
+          i = -2;
+      if(i >= 0)
+        {
+        hosts[host_index].base = ints[1];
+        hosts[host_index].irq = (ints[0] == 2)? ints[2] : 0;
+        host_index++;
+        }
+      }
+    }
+  }
+
+static int sym53c416_test(int base)
+  {
+  outb(RESET_CHIP, base + COMMAND_REG);
+  outb(NOOP, base + COMMAND_REG);
+  if(inb(base + COMMAND_REG) != NOOP)
+    return 0;
+  if(!inb(base + TC_HIGH) || inb(base + TC_HIGH) == 0xFF)
+    return 0;
+  if((inb(base + PIO_INT_REG) & (FULL | EMPTY | CE | OUE | FIE | EIE)) != EMPTY)
+    return 0;
+  return 1;
+  }
+
+void sym53c416_probe(void)
+  {
+  int *base = probeaddrs;
+  int ints[2];
+
+  ints[0] = 1;
+  for(; *base; base++)
+    if(!check_region(*base, IO_RANGE) && sym53c416_test(*base))
+      {
+      ints[1] = *base;
+      sym53c416_setup(NULL, ints);
+      }
+  }
+
+int sym53c416_detect(Scsi_Host_Template *tpnt)
+  {
+  unsigned long flags;
+  struct Scsi_Host * shpnt = NULL;
+  int i;
+  int count;
+
+#ifdef MODULE
+  int ints[3];
+
+  ints[0] = 2;
+  if(sym53c416_base)
+    {
+    ints[1] = sym53c416_base;
+    ints[2] = sym53c416_irq;
+    sym53c416_setup(NULL, ints);
+    }
+  if(sym53c416_base_1)
+    {
+    ints[1] = sym53c416_base_1;
+    ints[2] = sym53c416_irq_1;
+    sym53c416_setup(NULL, ints);
+    }
+  if(sym53c416_base_2)
+    {
+    ints[1] = sym53c416_base_2;
+    ints[2] = sym53c416_irq_2;
+    sym53c416_setup(NULL, ints);
+    }
+  if(sym53c416_base_3)
+    {
+    ints[1] = sym53c416_base_3;
+    ints[2] = sym53c416_irq_3;
+    sym53c416_setup(NULL, ints);
+    }
+#endif
+
+  printk("sym53c416.c: %s\n", VERSION_STRING);
+
+  sym53c416_probe();
+
+  /* Now we register and set up each host adapter found... */
+  for(count = 0, i = 0; i < host_index; i++)
+    if(!sym53c416_test(hosts[i].base))
+      printk("No sym53c416 found at address 0x%03x\n", hosts[i].base);
+    else
+      {
+      if(hosts[i].irq == 0)
+        /* We don't have an irq yet, so we should probe for one */
+        if((hosts[i].irq = sym53c416_probeirq(hosts[i].base, hosts[i].scsi_id)) == 0)
+          printk("irq autoprobing failed for sym53c416 at address 0x%03x\n", hosts[i].base);
+      if(hosts[i].irq && !check_region(hosts[i].base, IO_RANGE))
+        {
+        shpnt = scsi_register(tpnt, 0);
+        save_flags(flags);
+        cli();
+        /* Request for specified IRQ */
+        if(request_irq(hosts[i].irq, sym53c416_intr_handle, 0, ID, NULL))
+          {
+          restore_flags(flags);
+          printk("Unable to assign IRQ %d\n", hosts[i].irq);
+          scsi_unregister(shpnt);
+          }
+        else
+          {
+          /* Inform the kernel of our IO range */
+          request_region(hosts[i].base, IO_RANGE, ID);
+          shpnt->unique_id = hosts[i].base;
+          shpnt->io_port = hosts[i].base;
+          shpnt->n_io_port = IO_RANGE;
+          shpnt->irq = hosts[i].irq;
+          shpnt->this_id = hosts[i].scsi_id;
+          sym53c416_init(hosts[i].base, hosts[i].scsi_id);
+          count++;
+          restore_flags(flags);
+          }
+        }
+      }
+  return count;
+  }
+
+const char *sym53c416_info(struct Scsi_Host *SChost)
+  {
+  int i;
+  int base = SChost->io_port;
+  int irq = SChost->irq;
+  int scsi_id = 0;
+  int rev = inb(base + TC_HIGH);
+
+  for(i = 0; i < host_index; i++)
+    if(hosts[i].base == base)
+      scsi_id = hosts[i].scsi_id;
+  sprintf(info, "Symbios Logic 53c416 (rev. %d) at 0x%03x, irq %d, SCSI-ID %d, %s pio", rev, base, irq, scsi_id, (fastpio)? "fast" : "slow");
+  return info;
+  }
+
+int sym53c416_queuecommand(Scsi_Cmnd *SCpnt, void (*done)(Scsi_Cmnd *))
+  {
+  int base;
+  unsigned long flags = 0;
+  int i;
+
+  /* Store base register as we can have more than one controller in the system */
+  base = SCpnt->host->io_port;
+  current_command = SCpnt;                  /* set current command                */
+  current_command->scsi_done = done;        /* set ptr to done function           */
+  current_command->SCp.phase = command_ph;  /* currect phase is the command phase */
+  current_command->SCp.Status = 0;
+  current_command->SCp.Message = 0;
+
+  save_flags(flags);
+  cli();
+  outb(SCpnt->target, base + DEST_BUS_ID); /* Set scsi id target        */
+  outb(FLUSH_FIFO, base + COMMAND_REG);    /* Flush SCSI and PIO FIFO's */
+  /* Write SCSI command into the SCSI fifo */
+  for(i = 0; i < SCpnt->cmd_len; i++)
+    outb(SCpnt->cmnd[i], base + SCSI_FIFO);
+  /* Start selection sequence */
+  outb(SEL_WITHOUT_ATN_SEQ, base + COMMAND_REG);
+  /* Now an interrupt will be generated which we will catch in out interrupt routine */
+  restore_flags(flags);
+  return 0;
+  }
+
+static void internal_done(Scsi_Cmnd *SCpnt)
+  {
+  SCpnt->SCp.Status++;
+  }
+
+int sym53c416_command(Scsi_Cmnd *SCpnt)
+  {
+  sym53c416_queuecommand(SCpnt, internal_done);
+  SCpnt->SCp.Status = 0;
+  while(!SCpnt->SCp.Status)
+    barrier();
+  return SCpnt->result;
+  }
+
+int sym53c416_abort(Scsi_Cmnd *SCpnt)
+  {
+  printk("sym53c416_abort\n");
+
+  /* We don't know how to abort for the moment */
+  return SCSI_ABORT_SNOOZE;
+  }
+
+int sym53c416_reset(Scsi_Cmnd *SCpnt, unsigned int reset_flags)
+  {
+  int base;
+  int scsi_id = -1;
+  int i;
+
+  printk("sym53c416_reset\n");
+  base = SCpnt->host->io_port;
+  /* search scsi_id */
+  for(i = 0; i < host_index && scsi_id != -1; i++)
+    if(hosts[i].base == base)
+      scsi_id = hosts[i].scsi_id;
+  outb(RESET_CHIP, base + COMMAND_REG);
+  outb(NOOP | PIO_MODE, base + COMMAND_REG);
+  outb(RESET_SCSI_BUS, base + COMMAND_REG);
+  sym53c416_init(base, scsi_id);
+  return SCSI_RESET_PENDING;
+  }
+
+int sym53c416_bios_param(Disk *disk, kdev_t dev, int *ip)
+  {
+  int size;
+
+  size = disk->capacity;
+  ip[0] = 64;                         /* heads                        */
+  ip[1] = 32;                         /* sectors                      */
+  if((ip[2] = size >> 11) > 1024)     /* cylinders, test for big disk */
+    {
+    ip[0] = 255;                      /* heads                        */
+    ip[1] = 63;                       /* sectors                      */
+    ip[2] = size / (255 * 63);        /* cylinders                    */
+    }
+  return 0;
+  }
+
+/* Loadable module support */
+#ifdef MODULE
+
+#if LINUX_VERSION_CODE >= LinuxVersionCode(2,1,26)
+MODULE_AUTHOR("Lieven Willems");
+MODULE_PARM(sym53c416, "1-2i");
+MODULE_PARM(sym53c416_1, "1-2i");
+MODULE_PARM(sym53c416_2, "1-2i");
+MODULE_PARM(sym53c416_3, "1-2i");
+#endif
+
+Scsi_Host_Template driver_template = SYM53C416;
+
+#include "scsi_module.c"
+#endif

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)