patch-2.2.4 linux/arch/ppc/boot/mbxtty.c

• Lines: 202
• Date: Wed Dec 31 16:00:00 1969
• Orig file: v2.2.3/linux/arch/ppc/boot/mbxtty.c
• Orig date: Mon Oct 5 13:13:36 1998

diff -u --recursive --new-file v2.2.3/linux/arch/ppc/boot/mbxtty.c linux/arch/ppc/boot/mbxtty.c
@@ -1,201 +0,0 @@
-
-
-/* Minimal serial functions needed to send messages out the serial
- * port on the MBX console.
- *
- * The MBX uxes SMC1 for the serial port.  We reset the port and use
- * only the first BD that EPPC-Bug set up as a character FIFO.
- *
- * Later versions (at least 1.4, maybe earlier) of the MBX EPPC-Bug
- * use COM1 instead of SMC1 as the console port.  This kinda sucks
- * for the rest of the kernel, so here we force the use of SMC1 again.
- * I f**ked around for a day trying to figure out how to make EPPC-Bug
- * use SMC1, but gave up and decided to fix it here.
- */
-#include <linux/config.h>
-#include <linux/types.h>
-#ifdef CONFIG_MBX
-#include <asm/mbx.h>
-#endif
-#ifdef CONFIG_FADS
-#include <asm/fads.h>
-#endif
-#include "../8xx_io/commproc.h"
-
-#ifdef CONFIG_MBX
-#define MBX_CSR1	((volatile u_char *)0xfa100000)
-#define CSR1_COMEN	(u_char)0x02
-#endif
-
-static cpm8xx_t	*cpmp = (cpm8xx_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
-
-void
-serial_init(bd_t *bd)
-{
-	volatile smc_t		*sp;
-	volatile smc_uart_t	*up;
-	volatile cbd_t	*tbdf, *rbdf;
-	volatile cpm8xx_t	*cp;
-	uint	dpaddr, memaddr;
-
-	cp = cpmp;
-	sp = (smc_t*)&(cp->cp_smc[0]);
-	up = (smc_uart_t *)&cp->cp_dparam[PROFF_SMC1];
-
-	/* Disable transmitter/receiver.
-	*/
-	sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-
-#ifdef CONFIG_MBX
-	if (*MBX_CSR1 & CSR1_COMEN) {
-		/* COM1 is enabled.  Initialize SMC1 and use it for
-		 * the console port.
-		 */
-
-		/* Enable SDMA.
-		*/
-		((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sdcr = 1;
-
-		/* Use Port B for SMCs instead of other functions.
-		*/
-		cp->cp_pbpar |= 0x00000cc0;
-		cp->cp_pbdir &= ~0x00000cc0;
-		cp->cp_pbodr &= ~0x00000cc0;
-
-		/* Allocate space for two buffer descriptors in the DP ram.
-		 * For now, this address seems OK, but it may have to
-		 * change with newer versions of the firmware.
-		 */
-		dpaddr = 0x0800;
-
-		/* Grab a few bytes from the top of memory.  EPPC-Bug isn't
-		 * running any more, so we can do this.
-		 */
-		memaddr = (bd->bi_memsize - 32) & ~15;
-
-		/* Set the physical address of the host memory buffers in
-		 * the buffer descriptors.
-		 */
-		rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
-		rbdf->cbd_bufaddr = memaddr;
-		rbdf->cbd_sc = 0;
-		tbdf = rbdf + 1;
-		tbdf->cbd_bufaddr = memaddr+4;
-		tbdf->cbd_sc = 0;
-
-		/* Set up the uart parameters in the parameter ram.
-		*/
-		up->smc_rbase = dpaddr;
-		up->smc_tbase = dpaddr+sizeof(cbd_t);
-		up->smc_rfcr = SMC_EB;
-		up->smc_tfcr = SMC_EB;
-
-		/* Set UART mode, 8 bit, no parity, one stop.
-		 * Enable receive and transmit.
-		 */
-		sp->smc_smcmr = smcr_mk_clen(9) |  SMCMR_SM_UART;
-
-		/* Mask all interrupts and remove anything pending.
-		*/
-		sp->smc_smcm = 0;
-		sp->smc_smce = 0xff;
-
-		/* Set up the baud rate generator.
-		 * See 8xx_io/commproc.c for details.
-		 */
-		cp->cp_simode = 0x10000000;
-		cp->cp_brgc1 =
-			((((bd->bi_intfreq * 1000000)/16) / 9600) << 1) | CPM_BRG_EN;
-
-		/* Enable SMC1 for console output.
-		*/
-		*MBX_CSR1 &= ~CSR1_COMEN;
-	}
-	else {
-#endif
-		/* SMC1 is used as console port.
-		*/
-		tbdf = (cbd_t *)&cp->cp_dpmem[up->smc_tbase];
-		rbdf = (cbd_t *)&cp->cp_dpmem[up->smc_rbase];
-
-		/* Issue a stop transmit, and wait for it.
-		*/
-		cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SMC1,
-					CPM_CR_STOP_TX) | CPM_CR_FLG;
-		while (cp->cp_cpcr & CPM_CR_FLG);
-#ifdef CONFIG_MBX
-	}
-#endif
-
-	/* Make the first buffer the only buffer.
-	*/
-	tbdf->cbd_sc |= BD_SC_WRAP;
-	rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
-	/* Single character receive.
-	*/
-	up->smc_mrblr = 1;
-	up->smc_maxidl = 0;
-
-	/* Initialize Tx/Rx parameters.
-	*/
-	cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SMC1, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-	while (cp->cp_cpcr & CPM_CR_FLG);
-
-	/* Enable transmitter/receiver.
-	*/
-	sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
-}
-
-void
-serial_putchar(const char c)
-{
-	volatile cbd_t		*tbdf;
-	volatile char		*buf;
-	volatile smc_uart_t	*up;
-
-	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC1];
-	tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase];
-
-	/* Wait for last character to go.
-	*/
-	buf = (char *)tbdf->cbd_bufaddr;
-	while (tbdf->cbd_sc & BD_SC_READY);
-
-	*buf = c;
-	tbdf->cbd_datlen = 1;
-	tbdf->cbd_sc |= BD_SC_READY;
-}
-
-char
-serial_getc()
-{
-	volatile cbd_t		*rbdf;
-	volatile char		*buf;
-	volatile smc_uart_t	*up;
-	char			c;
-
-	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC1];
-	rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
-	/* Wait for character to show up.
-	*/
-	buf = (char *)rbdf->cbd_bufaddr;
-	while (rbdf->cbd_sc & BD_SC_EMPTY);
-	c = *buf;
-	rbdf->cbd_sc |= BD_SC_EMPTY;
-
-	return(c);
-}
-
-int
-serial_tstc()
-{
-	volatile cbd_t		*rbdf;
-	volatile smc_uart_t	*up;
-
-	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC1];
-	rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
-	return(!(rbdf->cbd_sc & BD_SC_EMPTY));
-}