patch-2.3.26 linux/drivers/net/sis900.h

• Lines: 249
• Date: Fri Nov 5 09:51:44 1999
• Orig file: v2.3.25/linux/drivers/net/sis900.h
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.3.25/linux/drivers/net/sis900.h linux/drivers/net/sis900.h
@@ -0,0 +1,248 @@
+/* sis900.h Definitions for SiS ethernet controllers including 7014/7016 and 900 
+ * Copyright 1999 Silicon Integrated System Corporation
+ * References:
+ *   SiS 7016 Fast Ethernet PCI Bus 10/100 Mbps LAN Controller with OnNow Support,
+ *	preliminary Rev. 1.0 Jan. 14, 1998
+ *   SiS 900 Fast Ethernet PCI Bus 10/100 Mbps LAN Single Chip with OnNow Support,
+ *	preliminary Rev. 1.0 Nov. 10, 1998
+ *   SiS 7014 Single Chip 100BASE-TX/10BASE-T Physical Layer Solution,
+ *	preliminary Rev. 1.0 Jan. 18, 1998
+ *   http://www.sis.com.tw/support/databook.htm
+ */
+
+/* MAC operationl registers of SiS 7016 and SiS 900 ehternet controller */
+/* The I/O extent, SiS 900 needs 256 bytes of io address */
+#define SIS900_TOTAL_SIZE 0x100
+
+/* Symbolic offsets to registers. */
+enum sis900_registers {
+	cr=0x0,                 //Command Register
+	cfg=0x4,                //Configuration Register
+	mear=0x8,               //EEPROM Access Register
+	ptscr=0xc,              //PCI Test Control Register
+	isr=0x10,               //Interrupt Status Register
+	imr=0x14,               //Interrupt Mask Register
+	ier=0x18,               //Interrupt Enable Register
+	epar=0x18,              //Enhanced PHY Access Register
+	txdp=0x20,              //Transmit Descriptor Pointer Register
+	txcfg=0x24,             //Transmit Configuration Register
+	rxdp=0x30,              //Receive Descriptor Pointer Register
+	rxcfg=0x34,             //Receive Configuration Register
+	flctrl=0x38,            //Flow Control Register
+	rxlen=0x3c,             //Receive Packet Length Register
+	rfcr=0x48,              //Receive Filter Control Register
+	rfdr=0x4C,              //Receive Filter Data Register
+	pmctrl=0xB0,            //Power Management Control Register
+	pmer=0xB4               //Power Management Wake-up Event Register
+};
+
+/* Symbolic names for bits in various registers */
+enum sis900_command_register_bits {
+	RESET   = 0x00000100, SWI = 0x00000080, RxRESET = 0x00000020,
+	TxRESET = 0x00000010, RxDIS = 0x00000008, RxENA = 0x00000004,
+	TxDIS   = 0x00000002, TxENA = 0x00000001
+};
+
+enum sis900_configuration_register_bits {
+	DESCRFMT = 0x00000100 /* 7016 specific */, REQALG = 0x00000080,
+	SB    = 0x00000040, POW = 0x00000020, EXD = 0x00000010, 
+	PESEL = 0x00000008, LPM = 0x00000004, BEM = 0x00000001
+};
+
+enum sis900_eeprom_access_reigster_bits {
+	MDC  = 0x00000040, MDDIR = 0x00000020, MDIO = 0x00000010, /* 7016 specific */ 
+	EECS = 0x00000008, EECLK = 0x00000004, EEDO = 0x00000002,
+	EEDI = 0x00000001
+};
+
+enum sis900_interrupt_register_bits {
+	WKEVT  = 0x10000000, TxPAUSEEND = 0x08000000, TxPAUSE = 0x04000000,
+	TxRCMP = 0x02000000, RxRCMP = 0x01000000, DPERR = 0x00800000,
+	SSERR  = 0x00400000, RMABT  = 0x00200000, RTABT = 0x00100000,
+	RxSOVR = 0x00010000, HIBERR = 0x00008000, SWINT = 0x00001000,
+	MIBINT = 0x00000800, TxURN  = 0x00000400, TxIDLE  = 0x00000200,
+	TxERR  = 0x00000100, TxDESC = 0x00000080, TxOK  = 0x00000040,
+	RxORN  = 0x00000020, RxIDLE = 0x00000010, RxEARLY = 0x00000008,
+	RxERR  = 0x00000004, RxDESC = 0x00000002, RxOK  = 0x00000001
+};
+
+enum sis900_interrupt_enable_reigster_bits {
+	IE = 0x00000001
+};
+
+/* maximum dma burst fro transmission and receive*/
+#define MAX_DMA_RANGE	7	/* actually 0 means MAXIMUM !! */
+#define TxMXDMA_shift   	20
+#define RxMXDMA_shift    20
+#define TX_DMA_BURST    	0
+#define RX_DMA_BURST    	0
+
+/* transmit FIFO threshholds */
+#define TX_FILL_THRESH   16	/* 1/4 FIFO size */
+#define TxFILLT_shift   	8
+#define TxDRNT_shift    	0
+#define TxDRNT_100      	48	/* 3/4 FIFO size */
+#define TxDRNT_10		16 	/* 1/2 FIFO size */
+
+enum sis900_transmit_config_register_bits {
+	TxCSI = 0x80000000, TxHBI = 0x40000000, TxMLB = 0x20000000,
+	TxATP = 0x10000000, TxIFG = 0x0C000000, TxFILLT = 0x00003F00,
+	TxDRNT = 0x0000003F
+};
+
+/* recevie FIFO thresholds */
+#define RxDRNT_shift     1
+#define RxDRNT_100	24	/* 3/4 FIFO size */
+#define RxDRNT_10		16 	/* 1/2 FIFO size */
+
+enum sis900_reveive_config_register_bits {
+	RxAEP  = 0x80000000, RxARP = 0x40000000, RxATX = 0x10000000,
+	RxAJAB = 0x08000000, RxDRNT = 0x0000007F
+};
+
+#define RFAA_shift      28
+#define RFADDR_shift    16
+
+enum sis900_receive_filter_control_register_bits {
+	RFEN  = 0x80000000, RFAAB = 0x40000000, RFAAM = 0x20000000,
+	RFAAP = 0x10000000, RFPromiscuous = (RFAAB|RFAAM|RFAAP)
+};
+
+enum sis900_reveive_filter_data_mask {
+	RFDAT =  0x0000FFFF
+};
+
+/* EEPROM Addresses */
+enum sis900_eeprom_address {
+	EEPROMSignature = 0x00, EEPROMVendorID = 0x02, EEPROMDeviceID = 0x03,
+	EEPROMMACAddr   = 0x08, EEPROMChecksum = 0x0b
+};
+
+/* The EEPROM commands include the alway-set leading bit. Refer to NM93Cxx datasheet */
+enum sis900_eeprom_command {
+	EEread     = 0x0180, EEwrite    = 0x0140, EEerase = 0x01C0, 
+	EEwriteEnable = 0x0130, EEwriteDisable = 0x0100,
+	EEeraseAll = 0x0120, EEwriteAll = 0x0110, 
+	EEaddrMask = 0x013F, EEcmdShift = 16
+};
+
+/* Manamgement Data I/O (mdio) frame */
+#define MIIread         0x6000
+#define MIIwrite        0x5002
+#define MIIpmdShift     7
+#define MIIregShift     2
+#define MIIcmdLen       16
+#define MIIcmdShift     16
+
+/* Buffer Descriptor Status*/
+enum sis900_buffer_status {
+	OWN    = 0x80000000, MORE   = 0x40000000, INTR = 0x20000000,
+	SUPCRC = 0x10000000, INCCRC = 0x10000000,
+	OK     = 0x08000000, DSIZE  = 0x00000FFF
+};
+/* Status for TX Buffers */
+enum sis900_tx_buffer_status {
+	ABORT   = 0x04000000, UNDERRUN = 0x02000000, NOCARRIER = 0x01000000,
+	DEFERD  = 0x00800000, EXCDEFER = 0x00400000, OWCOLL    = 0x00200000,
+	EXCCOLL = 0x00100000, COLCNT   = 0x000F0000
+};
+
+enum sis900_rx_bufer_status {
+	OVERRUN = 0x02000000, DEST = 0x00800000,     BCAST = 0x01800000,
+	MCAST   = 0x01000000, UNIMATCH = 0x00800000, TOOLONG = 0x00400000,
+	RUNT    = 0x00200000, RXISERR  = 0x00100000, CRCERR  = 0x00080000,
+	FAERR   = 0x00040000, LOOPBK   = 0x00020000, RXCOL   = 0x00010000
+};
+
+/* MII register offsets */
+enum mii_registers {
+	MII_CONTROL = 0x0000, MII_STATUS = 0x0001, MII_PHY_ID0 = 0x0002,
+	MII_PHY_ID1 = 0x0003, MII_ANADV  = 0x0004, MII_ANLPAR  = 0x0005,
+	MII_ANEXT   = 0x0006
+};
+
+/* mii registers specific to SiS 900 */
+enum sis_mii_registers {
+	MII_CONFIG1 = 0x0010, MII_CONFIG2 = 0x0011, MII_STSOUT = 0x0012,
+	MII_MASK    = 0x0013
+};
+
+/* mii registers specific to AMD 79C901 */
+enum amd_mii_registers {
+	MII_STATUS_SUMMARY = 0x0018
+};
+
+/* MII Control register bit definitions. */
+enum mii_control_register_bits {
+	MII_CNTL_FDX     = 0x0100, MII_CNTL_RST_AUTO = 0x0200, 
+	MII_CNTL_ISOLATE = 0x0400, MII_CNTL_PWRDWN   = 0x0800,
+	MII_CNTL_AUTO    = 0x1000, MII_CNTL_SPEED    = 0x2000,
+	MII_CNTL_LPBK    = 0x4000, MII_CNTL_RESET    = 0x8000
+};
+
+/* MII Status register bit  */
+enum mii_status_register_bits {
+	MII_STAT_EXT    = 0x0001, MII_STAT_JAB        = 0x0002, 
+	MII_STAT_LINK   = 0x0004, MII_STAT_CAN_AUTO   = 0x0008, 
+	MII_STAT_FAULT  = 0x0010, MII_STAT_AUTO_DONE  = 0x0020,
+	MII_STAT_CAN_T  = 0x0800, MII_STAT_CAN_T_FDX  = 0x1000,
+	MII_STAT_CAN_TX = 0x2000, MII_STAT_CAN_TX_FDX = 0x4000,
+	MII_STAT_CAN_T4 = 0x8000
+};
+
+#define		MII_ID1_OUI_LO		0xFC00	/* low bits of OUI mask */
+#define		MII_ID1_MODEL		0x03F0	/* model number */
+#define		MII_ID1_REV		0x000F	/* model number */
+
+/* MII NWAY Register Bits ...
+   valid for the ANAR (Auto-Negotiation Advertisement) and
+   ANLPAR (Auto-Negotiation Link Partner) registers */
+enum mii_nway_register_bits {
+	MII_NWAY_NODE_SEL = 0x001f, MII_NWAY_CSMA_CD = 0x0001,
+	MII_NWAY_T	  = 0x0020, MII_NWAY_T_FDX   = 0x0040,
+	MII_NWAY_TX       = 0x0080, MII_NWAY_TX_FDX  = 0x0100,
+	MII_NWAY_T4       = 0x0200, MII_NWAY_PAUSE   = 0x0400,
+	MII_NWAY_RF       = 0x2000, MII_NWAY_ACK     = 0x4000,
+	MII_NWAY_NP       = 0x8000
+};
+
+enum mii_stsout_register_bits {
+	MII_STSOUT_LINK_FAIL = 0x4000,
+	MII_STSOUT_SPD       = 0x0080, MII_STSOUT_DPLX = 0x0040
+};
+
+enum mii_stssum_register_bits {
+	MII_STSSUM_LINK = 0x0008, MII_STSSUM_DPLX = 0x0004,
+	MII_STSSUM_AUTO = 0x0002, MII_STSSUM_SPD  = 0x0001
+};
+
+#define FDX_CAPABLE_DUPLEX_UNKNOWN      0
+#define FDX_CAPABLE_HALF_SELECTED       1
+#define FDX_CAPABLE_FULL_SELECTED       2
+
+#define HW_SPEED_UNCONFIG		0
+#define HW_SPEED_HOME		1
+#define HW_SPEED_10_MBPS        	10
+#define HW_SPEED_100_MBPS       	100
+#define HW_SPEED_DEFAULT        	(HW_SPEED_100_MBPS)
+
+#define CRC_SIZE                4
+#define MAC_HEADER_SIZE         14
+
+#define TX_BUF_SIZE     1536
+#define RX_BUF_SIZE     1536
+
+#define NUM_TX_DESC     16      	/* Number of Tx descriptor registers. */
+#define NUM_RX_DESC     16       	/* Number of Rx descriptor registers. */
+
+#define TRUE            1
+#define FALSE           0
+
+/* PCI stuff, should be move to pic.h */
+#define PCI_DEVICE_ID_SI_900	0x900   
+#define PCI_DEVICE_ID_SI_7016	0x7016  
+
+/* ioctl for accessing MII transveiver */
+#define SIOCGMIIPHY (SIOCDEVPRIVATE)		/* Get the PHY in use. */
+#define SIOCGMIIREG (SIOCDEVPRIVATE+1)		/* Read a PHY register. */
+#define SIOCSMIIREG (SIOCDEVPRIVATE+2)		/* Write a PHY register */