patch-2.1.126 linux/Documentation/sound/MultiSound
Next file: linux/Documentation/stallion.txt
Previous file: linux/Documentation/powerpc/zImage_layout.txt
Back to the patch index
Back to the overall index
- Lines: 1288
- Date:
Fri Oct 9 11:56:59 1998
- Orig file:
v2.1.125/linux/Documentation/sound/MultiSound
- Orig date:
Tue Aug 18 22:02:01 1998
diff -u --recursive --new-file v2.1.125/linux/Documentation/sound/MultiSound linux/Documentation/sound/MultiSound
@@ -1,180 +1,476 @@
-Getting Firmware
-~~~~~~~~~~~~~~~~
-
-See the end of this document on how to obtain and create the necessary
-firmware files.
-
-
-Supported Features
-~~~~~~~~~~~~~~~~~~
-
-Currently digital audio and mixer functionality is supported. (memory
-mapped digital audio is not yet supported). Modular MultiSound
-support is composed of the following modules:
-
-msnd - MultiSound base (requires soundcore)
-msnd_classic - Base audio/mixer support for Classic, Monetery and
- Tahiti cards
-msnd_pinnacle - Base audio/mixer support for Pinnacle and Fiji cards
-
-
-Important Notes - Read Before Using
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-* The firmware files are not included (may change in future). You
-must obtain these images from Turtle Beach (they are included in the
-MultiSound Development Kits), and place them in /etc/sound for
-example, and give the full paths in the Linux configuration. Please
-note these files must be binary files, not assembler.
-
-* You need the following information to use this driver: the card's
-I/O base (i.e. 0x250), the IRQ (i.e. 5), and the shared memory area
-(i.e. 0xd8000).
-
-* Probing is not currently implemented, and only the msnd_classic
-driver will actually program the card's IRQ and SMA locations; the
-msnd_pinnacle is primarily for use with the card in PnP mode, however
-it should work if you know what the card's resource values are (this
-will change in the future).
-
-* Note the Turtle Beach Pinnacle card contains a Kurzweil MA-1
-synthesizer with an MPU compatible interface, which should work with
-the mpu401 module. You must know the resource values of the MA-1.
-
-
-Examples
-~~~~~~~~
-
-* If you have a MultiSound Classic/Monterey/Tahiti:
-
-insmod soundcore
-insmod msnd
-insmod msnd_classic io=0x290 irq=7 mem=0xd0000
-
-* If you have a MultiSound Pinnacle:
-
-insmod soundcore
-insmod msnd
-insmod msnd_pinnacle io=0x210 irq=5 mem=0xd8000
-
-* To use the MPU-compatible Kurzweil synth on the Pinnacle, add the
-following:
-
-insmod sound
-insmod mpu401 io=0x330 irq=9
-
-
-msnd_classic, msnd_pinnacle Required Options
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-If the following options are not given, the module will not load.
-Examine the kernel message log for informative error messages.
-WARNING--probing isn't supported so try to make sure you have the
-correct shared memory area, otherwise you may experience problems.
-
-io I/O base of DSP, e.g. io=0x210
-irq IRQ number, e.g. irq=5
-mem Shared memory area, e.g. mem=0xd8000
-
-
-msnd_classic, msnd_pinnacle Additional Options
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-fifosize The digital audio FIFOs, in kilobytes. The
- default is 64kB (two FIFOs are allocated, so
- this uses up 128kB).
-
-calibrate_signal Setting this to one calibrates the ADCs to the
- signal, zero calibrates to the card (defaults
- to zero).
-
-
-msnd_pinnacle Additional Options
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-digital Specify digital=1 to enable the S/PDIF input
- if you have the digital daughterboard
- adapter. This will enable access to the
- DIGITAL1 input for the soundcard in the mixer.
- Some mixer programs might have trouble setting
- the DIGITAL1 source as an input. If you have
- trouble, you can try the setdigital.c program
- at the bottom of this document.
-
-
-Obtaining and Creating Firmware Files
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
- For the Classic/Tahiti/Monterey
- ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-Download to /tmp and unzip the following file from Turtle Beach:
-
- ftp://ftp.tbeach.com/pub/tbs/pinn/msndvkit.zip
-
-When unzipped, unzip the file named MsndFiles.zip. Then copy the
-following firmware files to /etc/sound (note the file renaming):
-
- cp DSPCODE/MSNDINIT.BIN /etc/sound/msndinit.bin
- cp DSPCODE/MSNDPERM.REB /etc/sound/msndperm.bin
-
-When configuring the Linux kernel, specify /etc/sound/msndinit.bin and
-/etc/sound/msndperm.bin for the two firmware files (Linux kernel
-versions older than 2.2 do not ask for firmware paths, and are
-hardcoded to /etc/sound).
-
-
- For the Pinnacle/Fiji
- ~~~~~~~~~~~~~~~~~~~~~
-
-Download to /tmp and unzip the following file from Turtle Beach (be
-sure to use the entire URL; some have had trouble navigating to the
-URL):
-
- ftp://ftp.tbeach.com/oldpub/tbs/pinn/pnddk100.zip
-
-Put the following lines into a file named conv.l (between the start
-and end lines):
-
--- conv.l start --
-%%
-[ \n\t,\r]
-\;.*
-DB
-[0-9A-Fa-f]+H { int n; sscanf(yytext, "%xH", &n); printf("%c", n); }
--- conv.l end --
-
-Then, compile the conv program with GNU make with the following
-command:
-
- make LEX=flex LOADLIBES=-lfl conv
-
-This should give you an executable named conv. Now, we create the
-binary firmware files by doing the following conversion (assuming the
-archive unpacked into a directory named PINNDDK):
-
- ./conv < PINNDDK/dspcode/pndspini.asm > /etc/sound/pndspini.bin
- ./conv < PINNDDK/dspcode/pndsperm.asm > /etc/sound/pndsperm.bin
-
-The conv (and conv.l) program is not needed after conversion and can
-be safely deleted. Then, when configuring the Linux kernel, specify
-/etc/sound/pndspini.bin and /etc/sound/pndsperm.bin for the two
-firmware files (Linux kernel versions older than 2.2 do not ask for
-firmware paths, and are hardcoded to /etc/sound).
-
-
-Recording from the S/PDIF Input
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-If you have a Pinnacle or Fiji with S/PDIF input and want to set it as
-the input source, you can use this program if you have trouble trying
-to do it with a mixer program (be sure to insert the module with the
-digital=1 option).
-
-Compile with:
-cc -O setdigital.c -o setdigital
-
--- start setdigital.c --
+#! /bin/sh
+#
+# Turtle Beach MultiSound Driver Notes
+# -- Andrew Veliath <andrewtv@usa.net>
+#
+# Last update: September 10, 1998
+# Corresponding msnd driver: 0.8.2
+#
+# ** This file is a README (top part) and shell archive (bottom part).
+# The corresponding archived utility sources can be unpacked by
+# running `sh MultiSound' (the utilities are only needed for the
+# Pinnacle and Fiji cards). **
+#
+#
+# -=-=- Getting Firmware -=-=-
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# See the section `Obtaining and Creating Firmware Files' in this
+# document for instructions on obtaining the necessary firmware
+# files.
+#
+#
+# Supported Features
+# ~~~~~~~~~~~~~~~~~~
+#
+# Currently, full-duplex digital audio (/dev/dsp only, /dev/audio is
+# not currently available) and mixer functionality (/dev/mixer) are
+# supported (memory mapped digital audio is not yet supported).
+# Digital transfers and monitoring can be done as well if you have
+# the digital daughterboard (see the section on using the S/PDIF port
+# for more information).
+#
+# Support for the Turtle Beach MultiSound Hurricane architecture is
+# composed of the following modules (these can also operate compiled
+# into the kernel):
+#
+# msnd - MultiSound base (requires soundcore)
+#
+# msnd_classic - Base audio/mixer support for Classic, Monetery and
+# Tahiti cards
+#
+# msnd_pinnacle - Base audio/mixer support for Pinnacle and Fiji cards
+#
+#
+# Important Notes - Read Before Using
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# The firmware files are not included (may change in future). You
+# must obtain these images from Turtle Beach (they are included in
+# the MultiSound Development Kits), and place them in /etc/sound for
+# example, and give the full paths in the Linux configuration. If
+# you are compiling in support for the MultiSound driver rather than
+# using it as a module, these firmware files must be accessible
+# during kernel compilation.
+#
+# Please note these files must be binary files, not assembler. See
+# the section later in this document for instructions to obtain these
+# files.
+#
+#
+# Configuring Card Resources
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# ** This section is very important, as your card may not work at all
+# or your machine may crash if you do not do this correctly. **
+#
+# * Classic/Monterey/Tahiti
+#
+# These cards are configured through the driver msnd_classic. You must
+# know the io port, then the driver will select the irq and memory resources
+# on the card. It is up to you to know if these are free locations or now,
+# a conflict can lock the machine up.
+#
+# * Pinnacle/Fiji
+#
+# The Pinnacle and Fiji cards have an extra config port, either
+# 0x250, 0x260 or 0x270. This port can be disabled to have the card
+# configured strictly through PnP, however you lose the ability to
+# access the IDE controller and joystick devices on this card when
+# using PnP. The included pinnaclecfg program in this shell archive
+# can be used to configure the card in non-PnP mode, and in PnP mode
+# you can use isapnptools. These are described briefly here.
+#
+# pinnaclecfg is not required; you can use the msnd_pinnacle module
+# to fully configure the card as well. However, pinnaclecfg can be
+# used to change the resource values of a particular device after the
+# msnd_pinnacle module has been loaded. If you are compiling the
+# driver into the kernel, you must set these values during compile
+# time, however other peripheral resource values can be changed with
+# the pinnaclecfg program after the kernel is loaded.
+#
+#
+# *** PnP mode
+#
+# Use pnpdump to obtain a sample configuration if you can; I was able
+# to obtain one with the command `pnpdump 1 0x203' -- this may vary
+# for you (running pnpdump by itself did not work for me). Then,
+# edit this file and use isapnp to uncomment and set the card values.
+# Use these values when inserting the msnd_pinnacle module. Using
+# this method, you can set the resources for the DSP and the Kurzweil
+# synth (Pinnacle). Since Linux does not directly support PnP
+# devices, you may have difficulty when using the card in PnP mode
+# when it the driver is compiled into the kernel. Using non-PnP mode
+# is preferable in this case.
+#
+# Here is an example mypinnacle.conf for isapnp that sets the card to
+# io base 0x210, irq 5 and mem 0xd8000, and also sets the Kurzweil
+# synth to 0x330 and irq 9 (may need editing for your system):
+#
+# (READPORT 0x0203)
+# (CSN 2)
+# (IDENTIFY *)
+#
+# # DSP
+# (CONFIGURE BVJ0440/-1 (LD 0
+# (INT 0 (IRQ 5 (MODE +E))) (IO 0 (BASE 0x0210)) (MEM 0 (BASE 0x0d8000))
+# (ACT Y)))
+#
+# # Kurzweil Synth (Pinnacle Only)
+# (CONFIGURE BVJ0440/-1 (LD 1
+# (IO 0 (BASE 0x0330)) (INT 0 (IRQ 9 (MODE +E)))
+# (ACT Y)))
+#
+# (WAITFORKEY)
+#
+#
+# *** Non-PnP mode
+#
+# The second way is by running the card in non-PnP mode. This
+# actually has some advantages in that you can access some other
+# devices on the card, such as the joystick and IDE controller. To
+# configure the card, unpack this shell archive and build the
+# pinnaclecfg program. Using this program, you can assign the
+# resource values to the card's devices, or disable the devices. As
+# an alternative to using pinnaclecfg, you can specify many of the
+# configuration values when loading the msnd_pinnacle module (or
+# during kernel configuration when compiling the driver into the
+# kernel).
+#
+# If you specify cfg=0x250 for the msnd_pinnacle module, it
+# automatically configure the card to the given io, irq and memory
+# values using that config port (the config port is jumper selectable
+# on the card to 0x250, 0x260 or 0x270).
+#
+# See the `msnd_pinnacle Additional Options' section below for more
+# information on these parameters (also, if you compile the driver
+# directly into the kernel, these extra parameters can be useful
+# here).
+#
+#
+# ** It is very easy to cause problems in your machine if you choose a
+# resource value which is incorrect. **
+#
+#
+# Examples
+# ~~~~~~~~
+#
+# * MultiSound Classic/Monterey/Tahiti:
+#
+# insmod soundcore
+# insmod msnd
+# insmod msnd_classic io=0x290 irq=7 mem=0xd0000
+#
+# * MultiSound Pinnacle in PnP mode:
+#
+# insmod soundcore
+# insmod msnd
+# isapnp mypinnacle.conf
+# insmod msnd_pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values
+#
+# * MultiSound Pinnacle in non-PnP mode (replace 0x250 with your configuration port,
+# one of 0x250, 0x260 or 0x270):
+#
+# insmod soundcore
+# insmod msnd
+# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000
+#
+# * To use the MPU-compatible Kurzweil synth on the Pinnacle in PnP
+# mode, add the following (assumes you did `isapnp mypinnacle.conf'):
+#
+# insmod sound
+# insmod mpu401 io=0x330 irq=9 <-- match mypinnacle.conf values
+#
+# * To use the MPU-compatible Kurzweil synth on the Pinnacle in non-PnP
+# mode, add the following. Note how we first configure the peripheral's
+# resources, _then_ install a Linux driver for it:
+#
+# insmod sound
+# pinnaclecfg 0x250 mpu 0x330 9
+# insmod mpu401 io=0x330 irq=9
+#
+# -- OR you can use the following sequence without pinnaclecfg in non-PnP mode:
+#
+# insmod soundcore
+# insmod msnd
+# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9
+# insmod sound
+# insmod mpu401 io=0x330 irq=9
+#
+# * To setup the joystick port on the Pinnacle in non-PnP mode (though
+# you have to find the actual Linux joystick driver elsewhere), you
+# can use pinnaclecfg:
+#
+# pinnaclecfg 0x250 joystick 0x200
+#
+# -- OR you can configure this using msnd_pinnacle with the following:
+#
+# insmod soundcore
+# insmod msnd
+# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200
+#
+#
+# msnd_classic, msnd_pinnacle Required Options
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# If the following options are not given, the module will not load.
+# Examine the kernel message log for informative error messages.
+# WARNING--probing isn't supported so try to make sure you have the
+# correct shared memory area, otherwise you may experience problems.
+#
+# io I/O base of DSP, e.g. io=0x210
+# irq IRQ number, e.g. irq=5
+# mem Shared memory area, e.g. mem=0xd8000
+#
+#
+# msnd_classic, msnd_pinnacle Additional Options
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# fifosize The digital audio FIFOs, in kilobytes. If not
+# specified, the default will be used. Increasing
+# this value will reduce the chance of a FIFO
+# underflow at the expense of increasing overall
+# latency. For example, fifosize=512 will
+# allocate 512kB read and write FIFOs (1MB total).
+# While this may reduce dropouts, a heavy machine
+# load will undoubtedly starve the FIFO of data
+# and you will eventually get dropouts. One
+# option is to alter the scheduling priority of
+# the playback process, using `nice' or some form
+# of POSIX soft real-time scheduling.
+#
+# calibrate_signal Setting this to one calibrates the ADCs to the
+# signal, zero calibrates to the card (defaults
+# to zero).
+#
+#
+# msnd_pinnacle Additional Options
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# digital Specify digital=1 to enable the S/PDIF input
+# if you have the digital daughterboard
+# adapter. This will enable access to the
+# DIGITAL1 input for the soundcard in the mixer.
+# Some mixer programs might have trouble setting
+# the DIGITAL1 source as an input. If you have
+# trouble, you can try the setdigital.c program
+# at the bottom of this document.
+#
+# cfg Non-PnP configuration port for the Pinnacle
+# and Fiji (typically 0x250, 0x260 or 0x270,
+# depending on the jumper configuration). If
+# this option is omitted, then it is assumed
+# that the card is in PnP mode, and that the
+# specified DSP resource values are already
+# configured with PnP (i.e. it won't attempt to
+# do any sort of configuration).
+#
+# When the Pinnacle is in non-PnP mode, you can use the following
+# options to configure particular devices. If a full specification
+# for a device is not given, then the device is not configured. Note
+# that you still must use a Linux driver for any of these devices
+# once their resources are setup (such as the Linux joystick driver,
+# or the MPU401 driver from OSS for the Kurzweil synth).
+#
+# mpu_io I/O port of MPU (on-board Kurzweil synth)
+# mpu_irq IRQ of MPU (on-board Kurzweil synth)
+# ide_io0 First I/O port of IDE controller
+# ide_io1 Second I/O port of IDE controller
+# ide_irq IRQ IDE controller
+# joystick_io I/O port of joystick
+#
+#
+# Obtaining and Creating Firmware Files
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# For the Classic/Tahiti/Monterey
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# Download to /tmp and unzip the following file from Turtle Beach:
+#
+# ftp://ftp.voyetra.com/pub/tbs/msndcl/msndvkit.zip
+#
+# When unzipped, unzip the file named MsndFiles.zip. Then copy the
+# following firmware files to /etc/sound (note the file renaming):
+#
+# cp DSPCODE/MSNDINIT.BIN /etc/sound/msndinit.bin
+# cp DSPCODE/MSNDPERM.REB /etc/sound/msndperm.bin
+#
+# When configuring the Linux kernel, specify /etc/sound/msndinit.bin and
+# /etc/sound/msndperm.bin for the two firmware files (Linux kernel
+# versions older than 2.2 do not ask for firmware paths, and are
+# hardcoded to /etc/sound).
+#
+# If you are compiling the driver into the kernel, these files must
+# be accessible during compilation, but will not be needed later.
+# The files must remain, however, if the driver is used as a module.
+#
+#
+# For the Pinnacle/Fiji
+# ~~~~~~~~~~~~~~~~~~~~~
+#
+# Download to /tmp and unzip the following file from Turtle Beach (be
+# sure to use the entire URL; some have had trouble navigating to the
+# URL):
+#
+# ftp://ftp.voyetra.com/pub/tbs/pinn/pnddk100.zip
+#
+# Unpack this shell archive, and run make in the created directory
+# (you need a C compiler and flex to build the utilities). This
+# should give you the executables conv, pinnaclecfg and setdigital.
+# conv is only used temporarily here to create the firmware files,
+# while pinnaclecfg is used to configure the Pinnacle or Fiji card in
+# non-PnP mode, and setdigital can be used to set the S/PDIF input on
+# the mixer (pinnaclecfg and setdigital should be copied to a
+# convenient place, possibly run during system initialization).
+#
+# To generating the firmware files with the `conv' program, we create
+# the binary firmware files by doing the following conversion
+# (assuming the archive unpacked into a directory named PINNDDK):
+#
+# ./conv < PINNDDK/dspcode/pndspini.asm > /etc/sound/pndspini.bin
+# ./conv < PINNDDK/dspcode/pndsperm.asm > /etc/sound/pndsperm.bin
+#
+# The conv (and conv.l) program is not needed after conversion and can
+# be safely deleted. Then, when configuring the Linux kernel, specify
+# /etc/sound/pndspini.bin and /etc/sound/pndsperm.bin for the two
+# firmware files (Linux kernel versions older than 2.2 do not ask for
+# firmware paths, and are hardcoded to /etc/sound).
+#
+# If you are compiling the driver into the kernel, these files must
+# be accessible during compilation, but will not be needed later.
+# The files must remain, however, if the driver is used as a module.
+#
+#
+# Using Digital I/O with the S/PDIF Port
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#
+# If you have a Pinnacle or Fiji with the digital daughterboard and
+# want to set it as the input source, you can use this program if you
+# have trouble trying to do it with a mixer program (be sure to
+# insert the module with the digital=1 option, or say Y to the option
+# during compiled-in kernel operation). Upon selection of the S/PDIF
+# port, you should be able monitor and record from it.
+#
+# There is something to note about using the S/PDIF port. Digital
+# timing is taken from the digital signal, so if a signal is not
+# connected to the port and it is selected as recording input, you
+# will find PCM playback to be distorted in playback rate. Also,
+# attempting to record at a sampling rate other than the DAT rate may
+# be problematic (i.e. trying to record at 8000Hz when the DAT signal
+# is 44100Hz). If you have a problem with this, set the recording
+# input to the line in if you need to record at a rate other than
+# that of the DAT rate.
+#
+#
+# -- Shell archive attached below, just run `sh MultiSound' to extract.
+# Contains Pinnacle/Fiji utilities to convert firmware, configure
+# in non-PnP mode, and select the DIGITAL1 input for the mixer.
+#
+#
+#!/bin/sh
+# This is a shell archive (produced by GNU sharutils 4.2).
+# To extract the files from this archive, save it to some FILE, remove
+# everything before the `!/bin/sh' line above, then type `sh FILE'.
+#
+# Made on 1998-09-05 08:26 EDT by <andrewtv@ztransform.velsoft.com>.
+# Source directory was `/home/andrewtv/programming/pinnacle/pinnacle'.
+#
+# Existing files will *not* be overwritten unless `-c' is specified.
+#
+# This shar contains:
+# length mode name
+# ------ ---------- ------------------------------------------
+# 2111 -rw-rw-r-- MultiSound.d/setdigital.c
+# 10301 -rw-rw-r-- MultiSound.d/pinnaclecfg.c
+# 96 -rw-rw-r-- MultiSound.d/Makefile
+# 141 -rw-rw-r-- MultiSound.d/conv.l
+#
+save_IFS="${IFS}"
+IFS="${IFS}:"
+gettext_dir=FAILED
+locale_dir=FAILED
+first_param="$1"
+for dir in $PATH
+do
+ if test "$gettext_dir" = FAILED && test -f $dir/gettext \
+ && ($dir/gettext --version >/dev/null 2>&1)
+ then
+ set `$dir/gettext --version 2>&1`
+ if test "$3" = GNU
+ then
+ gettext_dir=$dir
+ fi
+ fi
+ if test "$locale_dir" = FAILED && test -f $dir/shar \
+ && ($dir/shar --print-text-domain-dir >/dev/null 2>&1)
+ then
+ locale_dir=`$dir/shar --print-text-domain-dir`
+ fi
+done
+IFS="$save_IFS"
+if test "$locale_dir" = FAILED || test "$gettext_dir" = FAILED
+then
+ echo=echo
+else
+ TEXTDOMAINDIR=$locale_dir
+ export TEXTDOMAINDIR
+ TEXTDOMAIN=sharutils
+ export TEXTDOMAIN
+ echo="$gettext_dir/gettext -s"
+fi
+touch -am 1231235999 $$.touch >/dev/null 2>&1
+if test ! -f 1231235999 && test -f $$.touch; then
+ shar_touch=touch
+else
+ shar_touch=:
+ echo
+ $echo 'WARNING: not restoring timestamps. Consider getting and'
+ $echo "installing GNU \`touch', distributed in GNU File Utilities..."
+ echo
+fi
+rm -f 1231235999 $$.touch
+#
+if mkdir _sh21233; then
+ $echo 'x -' 'creating lock directory'
+else
+ $echo 'failed to create lock directory'
+ exit 1
+fi
+# ============= MultiSound.d/setdigital.c ==============
+if test ! -d 'MultiSound.d'; then
+ $echo 'x -' 'creating directory' 'MultiSound.d'
+ mkdir 'MultiSound.d'
+fi
+if test -f 'MultiSound.d/setdigital.c' && test "$first_param" != -c; then
+ $echo 'x -' SKIPPING 'MultiSound.d/setdigital.c' '(file already exists)'
+else
+ $echo 'x -' extracting 'MultiSound.d/setdigital.c' '(text)'
+ sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/setdigital.c' &&
+/*********************************************************************
+X *
+X * setdigital.c - sets the DIGITAL1 input for a mixer
+X *
+X * Copyright (C) 1998 Andrew Veliath
+X *
+X * This program is free software; you can redistribute it and/or modify
+X * it under the terms of the GNU General Public License as published by
+X * the Free Software Foundation; either version 2 of the License, or
+X * (at your option) any later version.
+X *
+X * This program is distributed in the hope that it will be useful,
+X * but WITHOUT ANY WARRANTY; without even the implied warranty of
+X * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+X * GNU General Public License for more details.
+X *
+X * You should have received a copy of the GNU General Public License
+X * along with this program; if not, write to the Free Software
+X * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+X *
+X * $Id: setdigital.c,v 1.1 1998/08/29 03:32:33 andrewtv Exp $
+X *
+X ********************************************************************/
+X
#include <stdio.h>
#include <unistd.h>
#include <fcntl.h>
@@ -182,53 +478,586 @@
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <sys/soundcard.h>
-
+X
+int main(int argc, char *argv[])
+{
+X int fd;
+X unsigned long recmask, recsrc;
+X
+X if (argc != 2) {
+X fprintf(stderr, "usage: setdigital <mixer device>\n");
+X exit(1);
+X }
+X
+X if ((fd = open(argv[1], O_RDWR)) < 0) {
+X perror(argv[1]);
+X exit(1);
+X }
+X
+X if (ioctl(fd, SOUND_MIXER_READ_RECMASK, &recmask) < 0) {
+X fprintf(stderr, "error: ioctl read recording mask failed\n");
+X perror("ioctl");
+X close(fd);
+X exit(1);
+X }
+X
+X if (!(recmask & SOUND_MASK_DIGITAL1)) {
+X fprintf(stderr, "error: cannot find DIGITAL1 device in mixer\n");
+X close(fd);
+X exit(1);
+X }
+X
+X if (ioctl(fd, SOUND_MIXER_READ_RECSRC, &recsrc) < 0) {
+X fprintf(stderr, "error: ioctl read recording source failed\n");
+X perror("ioctl");
+X close(fd);
+X exit(1);
+X }
+X
+X recsrc |= SOUND_MASK_DIGITAL1;
+X
+X if (ioctl(fd, SOUND_MIXER_WRITE_RECSRC, &recsrc) < 0) {
+X fprintf(stderr, "error: ioctl write recording source failed\n");
+X perror("ioctl");
+X close(fd);
+X exit(1);
+X }
+X
+X close(fd);
+X
+X return 0;
+}
+SHAR_EOF
+ $shar_touch -am 0828233298 'MultiSound.d/setdigital.c' &&
+ chmod 0664 'MultiSound.d/setdigital.c' ||
+ $echo 'restore of' 'MultiSound.d/setdigital.c' 'failed'
+ if ( md5sum --help 2>&1 | grep 'sage: md5sum \[' ) >/dev/null 2>&1 \
+ && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then
+ md5sum -c << SHAR_EOF >/dev/null 2>&1 \
+ || $echo 'MultiSound.d/setdigital.c:' 'MD5 check failed'
+47720746d4367bae9954787c311c56fd MultiSound.d/setdigital.c
+SHAR_EOF
+ else
+ shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/setdigital.c'`"
+ test 2111 -eq "$shar_count" ||
+ $echo 'MultiSound.d/setdigital.c:' 'original size' '2111,' 'current size' "$shar_count!"
+ fi
+fi
+# ============= MultiSound.d/pinnaclecfg.c ==============
+if test -f 'MultiSound.d/pinnaclecfg.c' && test "$first_param" != -c; then
+ $echo 'x -' SKIPPING 'MultiSound.d/pinnaclecfg.c' '(file already exists)'
+else
+ $echo 'x -' extracting 'MultiSound.d/pinnaclecfg.c' '(text)'
+ sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/pinnaclecfg.c' &&
+/*********************************************************************
+X *
+X * pinnaclecfg.c - Pinnacle/Fiji Device Configuration Program
+X *
+X * This is for NON-PnP mode only. For PnP mode, use isapnptools.
+X *
+X * This is Linux-specific, and must be run with root permissions.
+X *
+X * Part of the Turtle Beach MultiSound Sound Card Driver for Linux
+X *
+X * Copyright (C) 1998 Andrew Veliath
+X *
+X * This program is free software; you can redistribute it and/or modify
+X * it under the terms of the GNU General Public License as published by
+X * the Free Software Foundation; either version 2 of the License, or
+X * (at your option) any later version.
+X *
+X * This program is distributed in the hope that it will be useful,
+X * but WITHOUT ANY WARRANTY; without even the implied warranty of
+X * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+X * GNU General Public License for more details.
+X *
+X * You should have received a copy of the GNU General Public License
+X * along with this program; if not, write to the Free Software
+X * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+X *
+X * $Id: pinnaclecfg.c,v 1.3 1998/08/29 03:32:32 andrewtv Exp $
+X *
+X ********************************************************************/
+X
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <errno.h>
+#include <unistd.h>
+#include <asm/io.h>
+#include <asm/types.h>
+X
+#define IREG_LOGDEVICE 0x07
+#define IREG_ACTIVATE 0x30
+#define LD_ACTIVATE 0x01
+#define LD_DISACTIVATE 0x00
+#define IREG_EECONTROL 0x3F
+#define IREG_MEMBASEHI 0x40
+#define IREG_MEMBASELO 0x41
+#define IREG_MEMCONTROL 0x42
+#define IREG_MEMRANGEHI 0x43
+#define IREG_MEMRANGELO 0x44
+#define MEMTYPE_8BIT 0x00
+#define MEMTYPE_16BIT 0x02
+#define MEMTYPE_RANGE 0x00
+#define MEMTYPE_HIADDR 0x01
+#define IREG_IO0_BASEHI 0x60
+#define IREG_IO0_BASELO 0x61
+#define IREG_IO1_BASEHI 0x62
+#define IREG_IO1_BASELO 0x63
+#define IREG_IRQ_NUMBER 0x70
+#define IREG_IRQ_TYPE 0x71
+#define IRQTYPE_HIGH 0x02
+#define IRQTYPE_LOW 0x00
+#define IRQTYPE_LEVEL 0x01
+#define IRQTYPE_EDGE 0x00
+X
+#define HIBYTE(w) ((BYTE)(((WORD)(w) >> 8) & 0xFF))
+#define LOBYTE(w) ((BYTE)(w))
+#define MAKEWORD(low,hi) ((WORD)(((BYTE)(low))|(((WORD)((BYTE)(hi)))<<8)))
+X
+typedef __u8 BYTE;
+typedef __u16 USHORT;
+typedef __u16 WORD;
+X
+static int config_port = -1;
+X
+static int msnd_write_cfg(int cfg, int reg, int value)
+{
+X outb(reg, cfg);
+X outb(value, cfg + 1);
+X if (value != inb(cfg + 1)) {
+X fprintf(stderr, "error: msnd_write_cfg: I/O error\n");
+X return -EIO;
+X }
+X return 0;
+}
+X
+static int msnd_read_cfg(int cfg, int reg)
+{
+X outb(reg, cfg);
+X return inb(cfg + 1);
+}
+X
+static int msnd_write_cfg_io0(int cfg, int num, WORD io)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_IO0_BASEHI, HIBYTE(io)))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_IO0_BASELO, LOBYTE(io)))
+X return -EIO;
+X return 0;
+}
+X
+static int msnd_read_cfg_io0(int cfg, int num, WORD *io)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X
+X *io = MAKEWORD(msnd_read_cfg(cfg, IREG_IO0_BASELO),
+X msnd_read_cfg(cfg, IREG_IO0_BASEHI));
+X
+X return 0;
+}
+X
+static int msnd_write_cfg_io1(int cfg, int num, WORD io)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_IO1_BASEHI, HIBYTE(io)))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_IO1_BASELO, LOBYTE(io)))
+X return -EIO;
+X return 0;
+}
+X
+static int msnd_read_cfg_io1(int cfg, int num, WORD *io)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X
+X *io = MAKEWORD(msnd_read_cfg(cfg, IREG_IO1_BASELO),
+X msnd_read_cfg(cfg, IREG_IO1_BASEHI));
+X
+X return 0;
+}
+X
+static int msnd_write_cfg_irq(int cfg, int num, WORD irq)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_IRQ_NUMBER, LOBYTE(irq)))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_IRQ_TYPE, IRQTYPE_EDGE))
+X return -EIO;
+X return 0;
+}
+X
+static int msnd_read_cfg_irq(int cfg, int num, WORD *irq)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X
+X *irq = msnd_read_cfg(cfg, IREG_IRQ_NUMBER);
+X
+X return 0;
+}
+X
+static int msnd_write_cfg_mem(int cfg, int num, int mem)
+{
+X WORD wmem;
+X
+X mem >>= 8;
+X mem &= 0xfff;
+X wmem = (WORD)mem;
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_MEMBASEHI, HIBYTE(wmem)))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_MEMBASELO, LOBYTE(wmem)))
+X return -EIO;
+X if (wmem && msnd_write_cfg(cfg, IREG_MEMCONTROL, (MEMTYPE_HIADDR | MEMTYPE_16BIT)))
+X return -EIO;
+X return 0;
+}
+X
+static int msnd_read_cfg_mem(int cfg, int num, int *mem)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X
+X *mem = MAKEWORD(msnd_read_cfg(cfg, IREG_MEMBASELO),
+X msnd_read_cfg(cfg, IREG_MEMBASEHI));
+X *mem <<= 8;
+X
+X return 0;
+}
+X
+static int msnd_activate_logical(int cfg, int num)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_write_cfg(cfg, IREG_ACTIVATE, LD_ACTIVATE))
+X return -EIO;
+X return 0;
+}
+X
+static int msnd_write_cfg_logical(int cfg, int num, WORD io0, WORD io1, WORD irq, int mem)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_write_cfg_io0(cfg, num, io0))
+X return -EIO;
+X if (msnd_write_cfg_io1(cfg, num, io1))
+X return -EIO;
+X if (msnd_write_cfg_irq(cfg, num, irq))
+X return -EIO;
+X if (msnd_write_cfg_mem(cfg, num, mem))
+X return -EIO;
+X if (msnd_activate_logical(cfg, num))
+X return -EIO;
+X return 0;
+}
+X
+static int msnd_read_cfg_logical(int cfg, int num, WORD *io0, WORD *io1, WORD *irq, int *mem)
+{
+X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num))
+X return -EIO;
+X if (msnd_read_cfg_io0(cfg, num, io0))
+X return -EIO;
+X if (msnd_read_cfg_io1(cfg, num, io1))
+X return -EIO;
+X if (msnd_read_cfg_irq(cfg, num, irq))
+X return -EIO;
+X if (msnd_read_cfg_mem(cfg, num, mem))
+X return -EIO;
+X return 0;
+}
+X
+static void usage(void)
+{
+X fprintf(stderr,
+X "\n"
+X "pinnaclecfg 1.0\n"
+X "\n"
+X "usage: pinnaclecfg <config port> [device config]\n"
+X "\n"
+X "This is for use with the card in NON-PnP mode only.\n"
+X "\n"
+X "Available devices (not all available for Fiji):\n"
+X "\n"
+X " Device Description\n"
+X " -------------------------------------------------------------------\n"
+X " reset Reset all devices (i.e. disable)\n"
+X " show Display current device configurations\n"
+X "\n"
+X " dsp <io> <irq> <mem> Audio device\n"
+X " mpu <io> <irq> Internal Kurzweil synth\n"
+X " ide <io0> <io1> <irq> On-board IDE controller\n"
+X " joystick <io> Joystick port\n"
+X "\n");
+X exit(1);
+}
+X
+static int cfg_reset(void)
+{
+X int i;
+X
+X for (i = 0; i < 4; ++i)
+X msnd_write_cfg_logical(config_port, i, 0, 0, 0, 0);
+X
+X return 0;
+}
+X
+static int cfg_show(void)
+{
+X int i;
+X int count = 0;
+X
+X for (i = 0; i < 4; ++i) {
+X WORD io0, io1, irq;
+X int mem;
+X msnd_read_cfg_logical(config_port, i, &io0, &io1, &irq, &mem);
+X switch (i) {
+X case 0:
+X if (io0 || irq || mem) {
+X printf("dsp 0x%x %d 0x%x\n", io0, irq, mem);
+X ++count;
+X }
+X break;
+X case 1:
+X if (io0 || irq) {
+X printf("mpu 0x%x %d\n", io0, irq);
+X ++count;
+X }
+X break;
+X case 2:
+X if (io0 || io1 || irq) {
+X printf("ide 0x%x 0x%x %d\n", io0, io1, irq);
+X ++count;
+X }
+X break;
+X case 3:
+X if (io0) {
+X printf("joystick 0x%x\n", io0);
+X ++count;
+X }
+X break;
+X }
+X }
+X
+X if (count == 0)
+X fprintf(stderr, "no devices configured\n");
+X
+X return 0;
+}
+X
+static int cfg_dsp(int argc, char *argv[])
+{
+X int io, irq, mem;
+X
+X if (argc < 3 ||
+X sscanf(argv[0], "0x%x", &io) != 1 ||
+X sscanf(argv[1], "%d", &irq) != 1 ||
+X sscanf(argv[2], "0x%x", &mem) != 1)
+X usage();
+X
+X if (!(io == 0x290 ||
+X io == 0x260 ||
+X io == 0x250 ||
+X io == 0x240 ||
+X io == 0x230 ||
+X io == 0x220 ||
+X io == 0x210 ||
+X io == 0x3e0)) {
+X fprintf(stderr, "error: io must be one of "
+X "210, 220, 230, 240, 250, 260, 290, or 3E0\n");
+X usage();
+X }
+X
+X if (!(irq == 5 ||
+X irq == 7 ||
+X irq == 9 ||
+X irq == 10 ||
+X irq == 11 ||
+X irq == 12)) {
+X fprintf(stderr, "error: irq must be one of "
+X "5, 7, 9, 10, 11 or 12\n");
+X usage();
+X }
+X
+X if (!(mem == 0xb0000 ||
+X mem == 0xc8000 ||
+X mem == 0xd0000 ||
+X mem == 0xd8000 ||
+X mem == 0xe0000 ||
+X mem == 0xe8000)) {
+X fprintf(stderr, "error: mem must be one of "
+X "0xb0000, 0xc8000, 0xd0000, 0xd8000, 0xe0000 or 0xe8000\n");
+X usage();
+X }
+X
+X return msnd_write_cfg_logical(config_port, 0, io, 0, irq, mem);
+}
+X
+static int cfg_mpu(int argc, char *argv[])
+{
+X int io, irq;
+X
+X if (argc < 2 ||
+X sscanf(argv[0], "0x%x", &io) != 1 ||
+X sscanf(argv[1], "%d", &irq) != 1)
+X usage();
+X
+X return msnd_write_cfg_logical(config_port, 1, io, 0, irq, 0);
+}
+X
+static int cfg_ide(int argc, char *argv[])
+{
+X int io0, io1, irq;
+X
+X if (argc < 3 ||
+X sscanf(argv[0], "0x%x", &io0) != 1 ||
+X sscanf(argv[0], "0x%x", &io1) != 1 ||
+X sscanf(argv[1], "%d", &irq) != 1)
+X usage();
+X
+X return msnd_write_cfg_logical(config_port, 2, io0, io1, irq, 0);
+}
+X
+static int cfg_joystick(int argc, char *argv[])
+{
+X int io;
+X
+X if (argc < 1 ||
+X sscanf(argv[0], "0x%x", &io) != 1)
+X usage();
+X
+X return msnd_write_cfg_logical(config_port, 3, io, 0, 0, 0);
+}
+X
int main(int argc, char *argv[])
{
- int fd;
- unsigned long recmask, recsrc;
-
- if (argc != 2) {
- fprintf(stderr, "usage: setdigital <mixer device>\n");
- exit(1);
- } else
-
- if ((fd = open(argv[1], O_RDWR)) < 0) {
- perror(argv[1]);
- exit(1);
- }
-
- if (ioctl(fd, SOUND_MIXER_READ_RECMASK, &recmask) < 0) {
- fprintf(stderr, "error: ioctl read recmask failed\n");
- perror("ioctl");
- close(fd);
- exit(1);
- }
-
- if (!(recmask & SOUND_MASK_DIGITAL1)) {
- fprintf(stderr, "error: cannot find DIGITAL1 device in mixer\n");
- close(fd);
- exit(1);
- }
-
- if (ioctl(fd, SOUND_MIXER_READ_RECSRC, &recsrc) < 0) {
- fprintf(stderr, "error: ioctl read recsrc failed\n");
- perror("ioctl");
- close(fd);
- exit(1);
- }
-
- recsrc |= SOUND_MASK_DIGITAL1;
-
- if (ioctl(fd, SOUND_MIXER_WRITE_RECSRC, &recsrc) < 0) {
- fprintf(stderr, "error: ioctl write recsrc failed\n");
- perror("ioctl");
- close(fd);
- exit(1);
- }
-
- close(fd);
-
- return 0;
+X char *device;
+X int rv = 0;
+X
+X --argc; ++argv;
+X
+X if (argc < 2)
+X usage();
+X
+X sscanf(argv[0], "0x%x", &config_port);
+X if (config_port != 0x250 && config_port != 0x260 && config_port != 0x270) {
+X fprintf(stderr, "error: <config port> must be 0x250, 0x260 or 0x270\n");
+X exit(1);
+X }
+X if (ioperm(config_port, 2, 1)) {
+X perror("ioperm");
+X fprintf(stderr, "note: pinnaclecfg must be run as root\n");
+X exit(1);
+X }
+X device = argv[1];
+X
+X argc -= 2; argv += 2;
+X
+X if (strcmp(device, "reset") == 0)
+X rv = cfg_reset();
+X else if (strcmp(device, "show") == 0)
+X rv = cfg_show();
+X else if (strcmp(device, "dsp") == 0)
+X rv = cfg_dsp(argc, argv);
+X else if (strcmp(device, "mpu") == 0)
+X rv = cfg_mpu(argc, argv);
+X else if (strcmp(device, "ide") == 0)
+X rv = cfg_ide(argc, argv);
+X else if (strcmp(device, "joystick") == 0)
+X rv = cfg_joystick(argc, argv);
+X else {
+X fprintf(stderr, "error: unknown device %s\n", device);
+X usage();
+X }
+X
+X if (rv)
+X fprintf(stderr, "error: device configuration failed\n");
+X
+X return 0;
}
--- end setdigital.c --
+SHAR_EOF
+ $shar_touch -am 0905082598 'MultiSound.d/pinnaclecfg.c' &&
+ chmod 0664 'MultiSound.d/pinnaclecfg.c' ||
+ $echo 'restore of' 'MultiSound.d/pinnaclecfg.c' 'failed'
+ if ( md5sum --help 2>&1 | grep 'sage: md5sum \[' ) >/dev/null 2>&1 \
+ && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then
+ md5sum -c << SHAR_EOF >/dev/null 2>&1 \
+ || $echo 'MultiSound.d/pinnaclecfg.c:' 'MD5 check failed'
+71f99b834a2845daae8ae034623e313e MultiSound.d/pinnaclecfg.c
+SHAR_EOF
+ else
+ shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/pinnaclecfg.c'`"
+ test 10301 -eq "$shar_count" ||
+ $echo 'MultiSound.d/pinnaclecfg.c:' 'original size' '10301,' 'current size' "$shar_count!"
+ fi
+fi
+# ============= MultiSound.d/Makefile ==============
+if test -f 'MultiSound.d/Makefile' && test "$first_param" != -c; then
+ $echo 'x -' SKIPPING 'MultiSound.d/Makefile' '(file already exists)'
+else
+ $echo 'x -' extracting 'MultiSound.d/Makefile' '(text)'
+ sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/Makefile' &&
+CC = gcc
+CFLAGS = -O
+PROGS = setdigital pinnaclecfg conv
+X
+all: $(PROGS)
+X
+clean:
+X rm -f $(PROGS)
+SHAR_EOF
+ $shar_touch -am 0828231798 'MultiSound.d/Makefile' &&
+ chmod 0664 'MultiSound.d/Makefile' ||
+ $echo 'restore of' 'MultiSound.d/Makefile' 'failed'
+ if ( md5sum --help 2>&1 | grep 'sage: md5sum \[' ) >/dev/null 2>&1 \
+ && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then
+ md5sum -c << SHAR_EOF >/dev/null 2>&1 \
+ || $echo 'MultiSound.d/Makefile:' 'MD5 check failed'
+ab95a049d10611a5e5d559a56965b33f MultiSound.d/Makefile
+SHAR_EOF
+ else
+ shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/Makefile'`"
+ test 96 -eq "$shar_count" ||
+ $echo 'MultiSound.d/Makefile:' 'original size' '96,' 'current size' "$shar_count!"
+ fi
+fi
+# ============= MultiSound.d/conv.l ==============
+if test -f 'MultiSound.d/conv.l' && test "$first_param" != -c; then
+ $echo 'x -' SKIPPING 'MultiSound.d/conv.l' '(file already exists)'
+else
+ $echo 'x -' extracting 'MultiSound.d/conv.l' '(text)'
+ sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/conv.l' &&
+%%
+[ \n\t,\r]
+\;.*
+DB
+[0-9A-Fa-f]+H { int n; sscanf(yytext, "%xH", &n); printf("%c", n); }
+%%
+int yywrap() { return 1; }
+main() { yylex(); }
+SHAR_EOF
+ $shar_touch -am 0828231798 'MultiSound.d/conv.l' &&
+ chmod 0664 'MultiSound.d/conv.l' ||
+ $echo 'restore of' 'MultiSound.d/conv.l' 'failed'
+ if ( md5sum --help 2>&1 | grep 'sage: md5sum \[' ) >/dev/null 2>&1 \
+ && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then
+ md5sum -c << SHAR_EOF >/dev/null 2>&1 \
+ || $echo 'MultiSound.d/conv.l:' 'MD5 check failed'
+d2411fc32cd71a00dcdc1f009e858dd2 MultiSound.d/conv.l
+SHAR_EOF
+ else
+ shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/conv.l'`"
+ test 141 -eq "$shar_count" ||
+ $echo 'MultiSound.d/conv.l:' 'original size' '141,' 'current size' "$shar_count!"
+ fi
+fi
+rm -fr _sh21233
+exit 0
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov