patch-2.1.70 linux/drivers/cdrom/cdu31a.h
Next file: linux/drivers/cdrom/cm206.c
Previous file: linux/drivers/cdrom/cdu31a.c
Back to the patch index
Back to the overall index
- Lines: 412
- Date:
Tue Dec 2 11:41:44 1997
- Orig file:
v2.1.69/linux/drivers/cdrom/cdu31a.h
- Orig date:
Wed Dec 31 16:00:00 1969
diff -u --recursive --new-file v2.1.69/linux/drivers/cdrom/cdu31a.h linux/drivers/cdrom/cdu31a.h
@@ -0,0 +1,411 @@
+/*
+ * Definitions for a Sony interface CDROM drive.
+ *
+ * Corey Minyard (minyard@wf-rch.cirr.com)
+ *
+ * Copyright (C) 1993 Corey Minyard
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+/*
+ * General defines.
+ */
+#define SONY_XA_DISK_TYPE 0x20
+
+/*
+ * Offsets (from the base address) and bits for the various write registers
+ * of the drive.
+ */
+#define SONY_CMD_REG_OFFSET 0
+#define SONY_PARAM_REG_OFFSET 1
+#define SONY_WRITE_REG_OFFSET 2
+#define SONY_CONTROL_REG_OFFSET 3
+# define SONY_ATTN_CLR_BIT 0x01
+# define SONY_RES_RDY_CLR_BIT 0x02
+# define SONY_DATA_RDY_CLR_BIT 0x04
+# define SONY_ATTN_INT_EN_BIT 0x08
+# define SONY_RES_RDY_INT_EN_BIT 0x10
+# define SONY_DATA_RDY_INT_EN_BIT 0x20
+# define SONY_PARAM_CLR_BIT 0x40
+# define SONY_DRIVE_RESET_BIT 0x80
+
+/*
+ * Offsets (from the base address) and bits for the various read registers
+ * of the drive.
+ */
+#define SONY_STATUS_REG_OFFSET 0
+# define SONY_ATTN_BIT 0x01
+# define SONY_RES_RDY_BIT 0x02
+# define SONY_DATA_RDY_BIT 0x04
+# define SONY_ATTN_INT_ST_BIT 0x08
+# define SONY_RES_RDY_INT_ST_BIT 0x10
+# define SONY_DATA_RDY_INT_ST_BIT 0x20
+# define SONY_DATA_REQUEST_BIT 0x40
+# define SONY_BUSY_BIT 0x80
+#define SONY_RESULT_REG_OFFSET 1
+#define SONY_READ_REG_OFFSET 2
+#define SONY_FIFOST_REG_OFFSET 3
+# define SONY_PARAM_WRITE_RDY_BIT 0x01
+# define SONY_PARAM_REG_EMPTY_BIT 0x02
+# define SONY_RES_REG_NOT_EMP_BIT 0x04
+# define SONY_RES_REG_FULL_BIT 0x08
+
+#define LOG_START_OFFSET 150 /* Offset of first logical sector */
+
+#define SONY_DETECT_TIMEOUT (8*HZ/10) /* Maximum amount of time
+ that drive detection code
+ will wait for response
+ from drive (in 1/100th's
+ of seconds). */
+
+#define SONY_JIFFIES_TIMEOUT 1000 /* Maximum number of times the
+ drive will wait/try for an
+ operation */
+#define SONY_RESET_TIMEOUT 100 /* Maximum number of times the
+ drive will wait/try a reset
+ operation */
+#define SONY_READY_RETRIES 20000 /* How many times to retry a
+ spin waiting for a register
+ to come ready */
+
+#define MAX_CDU31A_RETRIES 3 /* How many times to retry an
+ operation */
+
+/* Commands to request or set drive control parameters and disc information */
+#define SONY_REQ_DRIVE_CONFIG_CMD 0x00 /* Returns s_sony_drive_config */
+#define SONY_REQ_DRIVE_MODE_CMD 0x01
+#define SONY_REQ_DRIVE_PARAM_CMD 0x02
+#define SONY_REQ_MECH_STATUS_CMD 0x03
+#define SONY_REQ_AUDIO_STATUS_CMD 0x04
+#define SONY_SET_DRIVE_PARAM_CMD 0x10
+#define SONY_REQ_TOC_DATA_CMD 0x20 /* Returns s_sony_toc */
+#define SONY_REQ_SUBCODE_ADDRESS_CMD 0x21 /* Returns s_sony_subcode */
+#define SONY_REQ_UPC_EAN_CMD 0x22
+#define SONY_REQ_ISRC_CMD 0x23
+#define SONY_REQ_TOC_DATA_SPEC_CMD 0x24 /* Returns s_sony_session_toc */
+
+/* Commands to request information from the drive */
+#define SONY_READ_TOC_CMD 0x30 /* let the drive firmware grab the TOC */
+#define SONY_SEEK_CMD 0x31
+#define SONY_READ_CMD 0x32
+#define SONY_READ_BLKERR_STAT_CMD 0x34
+#define SONY_ABORT_CMD 0x35
+#define SONY_READ_TOC_SPEC_CMD 0x36
+
+/* Commands to control audio */
+#define SONY_AUDIO_PLAYBACK_CMD 0x40
+#define SONY_AUDIO_STOP_CMD 0x41
+#define SONY_AUDIO_SCAN_CMD 0x42
+
+/* Miscellaneous control commands */
+#define SONY_EJECT_CMD 0x50
+#define SONY_SPIN_UP_CMD 0x51
+#define SONY_SPIN_DOWN_CMD 0x52
+
+/* Diagnostic commands */
+#define SONY_WRITE_BUFFER_CMD 0x60
+#define SONY_READ_BUFFER_CMD 0x61
+#define SONY_DIAGNOSTICS_CMD 0x62
+
+
+/*
+ * The following are command parameters for the set drive parameter command
+ */
+#define SONY_SD_DECODE_PARAM 0x00
+#define SONY_SD_INTERFACE_PARAM 0x01
+#define SONY_SD_BUFFERING_PARAM 0x02
+#define SONY_SD_AUDIO_PARAM 0x03
+#define SONY_SD_AUDIO_VOLUME 0x04
+#define SONY_SD_MECH_CONTROL 0x05
+#define SONY_SD_AUTO_SPIN_DOWN_TIME 0x06
+
+/*
+ * The following are parameter bits for the mechanical control command
+ */
+#define SONY_AUTO_SPIN_UP_BIT 0x01
+#define SONY_AUTO_EJECT_BIT 0x02
+#define SONY_DOUBLE_SPEED_BIT 0x04
+
+/*
+ * The following extract information from the drive configuration about
+ * the drive itself.
+ */
+#define SONY_HWC_GET_LOAD_MECH(c) (c.hw_config[0] & 0x03)
+#define SONY_HWC_EJECT(c) (c.hw_config[0] & 0x04)
+#define SONY_HWC_LED_SUPPORT(c) (c.hw_config[0] & 0x08)
+#define SONY_HWC_DOUBLE_SPEED(c) (c.hw_config[0] & 0x10)
+#define SONY_HWC_GET_BUF_MEM_SIZE(c) ((c.hw_config[0] & 0xc0) >> 6)
+#define SONY_HWC_AUDIO_PLAYBACK(c) (c.hw_config[1] & 0x01)
+#define SONY_HWC_ELECTRIC_VOLUME(c) (c.hw_config[1] & 0x02)
+#define SONY_HWC_ELECTRIC_VOLUME_CTL(c) (c.hw_config[1] & 0x04)
+
+#define SONY_HWC_CADDY_LOAD_MECH 0x00
+#define SONY_HWC_TRAY_LOAD_MECH 0x01
+#define SONY_HWC_POPUP_LOAD_MECH 0x02
+#define SONY_HWC_UNKWN_LOAD_MECH 0x03
+
+#define SONY_HWC_8KB_BUFFER 0x00
+#define SONY_HWC_32KB_BUFFER 0x01
+#define SONY_HWC_64KB_BUFFER 0x02
+#define SONY_HWC_UNKWN_BUFFER 0x03
+
+/*
+ * This is the complete status returned from the drive configuration request
+ * command.
+ */
+struct s_sony_drive_config
+{
+ unsigned char exec_status[2];
+ char vendor_id[8];
+ char product_id[16];
+ char product_rev_level[8];
+ unsigned char hw_config[2];
+};
+
+/* The following is returned from the request subcode address command */
+struct s_sony_subcode
+{
+ unsigned char exec_status[2];
+ unsigned char address :4;
+ unsigned char control :4;
+ unsigned char track_num;
+ unsigned char index_num;
+ unsigned char rel_msf[3];
+ unsigned char reserved1;
+ unsigned char abs_msf[3];
+};
+
+#define MAX_TRACKS 100 /* The maximum tracks a disk may have. */
+/*
+ * The following is returned from the request TOC (Table Of Contents) command.
+ * (last_track_num-first_track_num+1) values are valid in tracks.
+ */
+struct s_sony_toc
+{
+ unsigned char exec_status[2];
+ unsigned char address0 :4;
+ unsigned char control0 :4;
+ unsigned char point0;
+ unsigned char first_track_num;
+ unsigned char disk_type;
+ unsigned char dummy0;
+ unsigned char address1 :4;
+ unsigned char control1 :4;
+ unsigned char point1;
+ unsigned char last_track_num;
+ unsigned char dummy1;
+ unsigned char dummy2;
+ unsigned char address2 :4;
+ unsigned char control2 :4;
+ unsigned char point2;
+ unsigned char lead_out_start_msf[3];
+ struct
+ {
+ unsigned char address :4;
+ unsigned char control :4;
+ unsigned char track;
+ unsigned char track_start_msf[3];
+ } tracks[MAX_TRACKS];
+
+ unsigned int lead_out_start_lba;
+};
+
+struct s_sony_session_toc
+{
+ unsigned char exec_status[2];
+ unsigned char session_number;
+ unsigned char address0 :4;
+ unsigned char control0 :4;
+ unsigned char point0;
+ unsigned char first_track_num;
+ unsigned char disk_type;
+ unsigned char dummy0;
+ unsigned char address1 :4;
+ unsigned char control1 :4;
+ unsigned char point1;
+ unsigned char last_track_num;
+ unsigned char dummy1;
+ unsigned char dummy2;
+ unsigned char address2 :4;
+ unsigned char control2 :4;
+ unsigned char point2;
+ unsigned char lead_out_start_msf[3];
+ unsigned char addressb0 :4;
+ unsigned char controlb0 :4;
+ unsigned char pointb0;
+ unsigned char next_poss_prog_area_msf[3];
+ unsigned char num_mode_5_pointers;
+ unsigned char max_start_outer_leadout_msf[3];
+ unsigned char addressb1 :4;
+ unsigned char controlb1 :4;
+ unsigned char pointb1;
+ unsigned char dummyb0_1[4];
+ unsigned char num_skip_interval_pointers;
+ unsigned char num_skip_track_assignments;
+ unsigned char dummyb0_2;
+ unsigned char addressb2 :4;
+ unsigned char controlb2 :4;
+ unsigned char pointb2;
+ unsigned char tracksb2[7];
+ unsigned char addressb3 :4;
+ unsigned char controlb3 :4;
+ unsigned char pointb3;
+ unsigned char tracksb3[7];
+ unsigned char addressb4 :4;
+ unsigned char controlb4 :4;
+ unsigned char pointb4;
+ unsigned char tracksb4[7];
+ unsigned char addressc0 :4;
+ unsigned char controlc0 :4;
+ unsigned char pointc0;
+ unsigned char dummyc0[7];
+ struct
+ {
+ unsigned char address :4;
+ unsigned char control :4;
+ unsigned char track;
+ unsigned char track_start_msf[3];
+ } tracks[MAX_TRACKS];
+
+ unsigned int start_track_lba;
+ unsigned int lead_out_start_lba;
+ unsigned int mint;
+ unsigned int maxt;
+};
+
+struct s_all_sessions_toc
+{
+ unsigned char sessions;
+ unsigned int track_entries;
+ unsigned char first_track_num;
+ unsigned char last_track_num;
+ unsigned char disk_type;
+ unsigned char lead_out_start_msf[3];
+ struct
+ {
+ unsigned char address :4;
+ unsigned char control :4;
+ unsigned char track;
+ unsigned char track_start_msf[3];
+ } tracks[MAX_TRACKS];
+
+ unsigned int start_track_lba;
+ unsigned int lead_out_start_lba;
+};
+
+
+/*
+ * The following are errors returned from the drive.
+ */
+
+/* Command error group */
+#define SONY_ILL_CMD_ERR 0x10
+#define SONY_ILL_PARAM_ERR 0x11
+
+/* Mechanism group */
+#define SONY_NOT_LOAD_ERR 0x20
+#define SONY_NO_DISK_ERR 0x21
+#define SONY_NOT_SPIN_ERR 0x22
+#define SONY_SPIN_ERR 0x23
+#define SONY_SPINDLE_SERVO_ERR 0x25
+#define SONY_FOCUS_SERVO_ERR 0x26
+#define SONY_EJECT_MECH_ERR 0x29
+#define SONY_AUDIO_PLAYING_ERR 0x2a
+#define SONY_EMERGENCY_EJECT_ERR 0x2c
+
+/* Seek error group */
+#define SONY_FOCUS_ERR 0x30
+#define SONY_FRAME_SYNC_ERR 0x31
+#define SONY_SUBCODE_ADDR_ERR 0x32
+#define SONY_BLOCK_SYNC_ERR 0x33
+#define SONY_HEADER_ADDR_ERR 0x34
+
+/* Read error group */
+#define SONY_ILL_TRACK_R_ERR 0x40
+#define SONY_MODE_0_R_ERR 0x41
+#define SONY_ILL_MODE_R_ERR 0x42
+#define SONY_ILL_BLOCK_SIZE_R_ERR 0x43
+#define SONY_MODE_R_ERR 0x44
+#define SONY_FORM_R_ERR 0x45
+#define SONY_LEAD_OUT_R_ERR 0x46
+#define SONY_BUFFER_OVERRUN_R_ERR 0x47
+
+/* Data error group */
+#define SONY_UNREC_CIRC_ERR 0x53
+#define SONY_UNREC_LECC_ERR 0x57
+
+/* Subcode error group */
+#define SONY_NO_TOC_ERR 0x60
+#define SONY_SUBCODE_DATA_NVAL_ERR 0x61
+#define SONY_FOCUS_ON_TOC_READ_ERR 0x63
+#define SONY_FRAME_SYNC_ON_TOC_READ_ERR 0x64
+#define SONY_TOC_DATA_ERR 0x65
+
+/* Hardware failure group */
+#define SONY_HW_FAILURE_ERR 0x70
+#define SONY_LEAD_IN_A_ERR 0x91
+#define SONY_LEAD_OUT_A_ERR 0x92
+#define SONY_DATA_TRACK_A_ERR 0x93
+
+/*
+ * The following are returned from the Read With Block Error Status command.
+ * They are not errors but information (Errors from the 0x5x group above may
+ * also be returned
+ */
+#define SONY_NO_CIRC_ERR_BLK_STAT 0x50
+#define SONY_NO_LECC_ERR_BLK_STAT 0x54
+#define SONY_RECOV_LECC_ERR_BLK_STAT 0x55
+#define SONY_NO_ERR_DETECTION_STAT 0x59
+
+/*
+ * The following is not an error returned by the drive, but by the code
+ * that talks to the drive. It is returned because of a timeout.
+ */
+#define SONY_TIMEOUT_OP_ERR 0x01
+#define SONY_SIGNAL_OP_ERR 0x02
+#define SONY_BAD_DATA_ERR 0x03
+
+
+/*
+ * The following are attention code for asynchronous events from the drive.
+ */
+
+/* Standard attention group */
+#define SONY_EMER_EJECT_ATTN 0x2c
+#define SONY_HW_FAILURE_ATTN 0x70
+#define SONY_MECH_LOADED_ATTN 0x80
+#define SONY_EJECT_PUSHED_ATTN 0x81
+
+/* Audio attention group */
+#define SONY_AUDIO_PLAY_DONE_ATTN 0x90
+#define SONY_LEAD_IN_ERR_ATTN 0x91
+#define SONY_LEAD_OUT_ERR_ATTN 0x92
+#define SONY_DATA_TRACK_ERR_ATTN 0x93
+#define SONY_AUDIO_PLAYBACK_ERR_ATTN 0x94
+
+/* Auto spin up group */
+#define SONY_SPIN_UP_COMPLETE_ATTN 0x24
+#define SONY_SPINDLE_SERVO_ERR_ATTN 0x25
+#define SONY_FOCUS_SERVO_ERR_ATTN 0x26
+#define SONY_TOC_READ_DONE_ATTN 0x62
+#define SONY_FOCUS_ON_TOC_READ_ERR_ATTN 0x63
+#define SONY_SYNC_ON_TOC_READ_ERR_ATTN 0x65
+
+/* Auto eject group */
+#define SONY_SPIN_DOWN_COMPLETE_ATTN 0x27
+#define SONY_EJECT_COMPLETE_ATTN 0x28
+#define SONY_EJECT_MECH_ERR_ATTN 0x29
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov