patch-2.1.70 linux/include/linux/aztcd.h

• Lines: 163
• Date: Wed Dec 31 16:00:00 1969
• Orig file: v2.1.69/linux/include/linux/aztcd.h
• Orig date: Tue Dec 2 09:49:40 1997

diff -u --recursive --new-file v2.1.69/linux/include/linux/aztcd.h linux/include/linux/aztcd.h
@@ -1,162 +0,0 @@
-/* $Id: aztcd.h,v 2.60 1997/11/29 09:51:22 root Exp root $
- *
- * Definitions for a AztechCD268 CD-ROM interface
- *	Copyright (C) 1994-98  Werner Zimmermann
- *
- *	based on Mitsumi CDROM driver by Martin Harriss
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation; either version 2 of the License, or
- *  (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the Free Software
- *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- *  History:	W.Zimmermann adaption to Aztech CD268-01A Version 1.3
- *		October 1994 Email: Werner.Zimmermann@fht-esslingen.de
- */
-
-/* *** change this to set the I/O port address of your CD-ROM drive,
-       set to '-1', if you want autoprobing */
-#define AZT_BASE_ADDR		-1
-
-/* list of autoprobing addresses (not more than 15), last value must be 0x000
-   Note: Autoprobing is only enabled, if AZT_BASE_ADDR is set to '-1' ! */
-#define AZT_BASE_AUTO 		{ 0x320, 0x300, 0x310, 0x330, 0x000 }
-
-/* Uncomment this, if your CDROM is connected to a Soundwave32-soundcard
-   and configure AZT_BASE_ADDR and AZT_SW32_BASE_ADDR */
-/*#define AZT_SW32 1
-*/
-
-#ifdef AZT_SW32 
-#define AZT_SW32_BASE_ADDR      0x220  /*I/O port base address of your soundcard*/
-#endif
-
-/* Set this to 1, if you want your tray to be locked, set to 0 to prevent tray 
-   from locking */
-#define AZT_ALLOW_TRAY_LOCK	1
-
-/*Set this to 1 to allow auto-eject when unmounting a disk, set to 0, if you 
-  don't want the auto-eject feature*/
-#define AZT_AUTO_EJECT          0
-
-/*Set this to 1, if you want to use incompatible ioctls for reading in raw and
-  cooked mode */
-#define AZT_PRIVATE_IOCTLS      1
-
-/*Set this to 1, if you want multisession support by the ISO fs. Even if you set 
-  this value to '0' you can use multisession CDs. In that case the drive's firm-
-  ware will do the appropriate redirection automatically. The CD will then look
-  like a single session CD (but nevertheless all data may be read). Please read 
-  chapter '5.1 Multisession support' in README.aztcd for details. Normally it's 
-  uncritical to leave this setting untouched */
-#define AZT_MULTISESSION        1
-
-/*Uncomment this, if you are using a linux kernel version prior to 2.1.0 */
-/*#define AZT_KERNEL_PRIOR_2_1 */
-
-/*---------------------------------------------------------------------------*/
-/*-----nothing to be configured for normal applications below this line------*/
-
-
-/* Increase this if you get lots of timeouts; if you get kernel panic, replace
-   STEN_LOW_WAIT by STEN_LOW in the source code */
-#define AZT_STATUS_DELAY	400       /*for timer wait, STEN_LOW_WAIT*/
-#define AZT_TIMEOUT		8000000   /*for busy wait STEN_LOW, DTEN_LOW*/
-#define AZT_FAST_TIMEOUT	10000     /*for reading the version string*/
-
-/* number of times to retry a command before giving up */
-#define AZT_RETRY_ATTEMPTS	3
-
-/* port access macros */
-#define CMD_PORT		azt_port
-#define DATA_PORT		azt_port
-#define STATUS_PORT		azt_port+1
-#define MODE_PORT		azt_port+2
-#ifdef  AZT_SW32                
- #define AZT_SW32_INIT          (unsigned int) (0xFF00 & (AZT_BASE_ADDR*16))
- #define AZT_SW32_CONFIG_REG    AZT_SW32_BASE_ADDR+0x16  /*Soundwave32 Config. Register*/
- #define AZT_SW32_ID_REG        AZT_SW32_BASE_ADDR+0x04  /*Soundwave32 ID Version Register*/
-#endif
-
-/* status bits */
-#define AST_CMD_CHECK		0x80		/* 1 = command error */
-#define AST_DOOR_OPEN		0x40		/* 1 = door is open */
-#define AST_NOT_READY		0x20		/* 1 = no disk in the drive */
-#define AST_DSK_CHG		0x02		/* 1 = disk removed or changed */
-#define AST_MODE                0x01            /* 0=MODE1, 1=MODE2 */
-#define AST_MODE_BITS		0x1C		/* Mode Bits */
-#define AST_INITIAL		0x0C		/* initial, only valid ... */
-#define AST_BUSY		0x04		/* now playing, only valid
-						   in combination with mode
-						   bits */
-/* flag bits */
-#define AFL_DATA		0x02		/* data available if low */
-#define AFL_STATUS		0x04		/* status available if low */
-#define AFL_OP_OK		0x01		/* OP_OK command correct*/
-#define AFL_PA_OK		0x02		/* PA_OK parameter correct*/
-#define AFL_OP_ERR		0x05		/* error in command*/
-#define AFL_PA_ERR		0x06		/* error in parameters*/
-#define POLLED			0x04		/* polled mode */
-
-/* commands */
-#define ACMD_SOFT_RESET		0x10		/* reset drive */
-#define ACMD_PLAY_READ		0x20		/* read data track in cooked mode */
-#define ACMD_PLAY_READ_RAW      0x21		/* reading in raw mode*/
-#define ACMD_SEEK               0x30            /* seek msf address*/
-#define ACMD_SEEK_TO_LEADIN     0x31		/* seek to leadin track*/
-#define ACMD_GET_ERROR		0x40		/* get error code */
-#define ACMD_GET_STATUS		0x41		/* get status */
-#define ACMD_GET_Q_CHANNEL      0x50		/* read info from q channel */
-#define ACMD_EJECT		0x60		/* eject/open tray */
-#define ACMD_CLOSE              0x61            /* close tray */
-#define ACMD_LOCK		0x71		/* lock tray closed */
-#define ACMD_UNLOCK		0x72		/* unlock tray */
-#define ACMD_PAUSE		0x80		/* pause */
-#define ACMD_STOP		0x81		/* stop play */
-#define ACMD_PLAY_AUDIO		0x90		/* play audio track */
-#define ACMD_SET_VOLUME		0x93		/* set audio level */
-#define ACMD_GET_VERSION	0xA0		/* get firmware version */
-#define ACMD_SET_DISK_TYPE	0xA1		/* set disk data mode */
-
-#define MAX_TRACKS		104
-
-struct msf {
-	unsigned char	min;
-	unsigned char	sec;
-	unsigned char	frame;
-};
-
-struct azt_Play_msf {
-	struct msf	start;
-	struct msf	end;
-};
-
-struct azt_DiskInfo {
-	unsigned char	first;
-        unsigned char   next;
-	unsigned char	last;
-	struct msf	diskLength;
-	struct msf	firstTrack;
-        unsigned char   multi;
-        struct msf      nextSession;
-        struct msf      lastSession;
-        unsigned char   xa;
-        unsigned char   audio;
-};
-
-struct azt_Toc {
-	unsigned char	ctrl_addr;
-	unsigned char	track;
-	unsigned char	pointIndex;
-	struct msf	trackTime;
-	struct msf	diskTime;
-};