patch-2.4.22 linux-2.4.22/include/asm-ia64/sn/sn1/hubio.h
Next file: linux-2.4.22/include/asm-ia64/sn/sn1/hubio_next.h
Previous file: linux-2.4.22/include/asm-ia64/sn/sn1/hubdev.h
Back to the patch index
Back to the overall index
- Lines: 5017
- Date:
1969-12-31 16:00:00.000000000 -0800
- Orig file:
linux-2.4.21/include/asm-ia64/sn/sn1/hubio.h
- Orig date:
2003-06-13 07:51:38.000000000 -0700
diff -urN linux-2.4.21/include/asm-ia64/sn/sn1/hubio.h linux-2.4.22/include/asm-ia64/sn/sn1/hubio.h
@@ -1,5016 +0,0 @@
-/* $Id$
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1992-1997,2000-2002 Silicon Graphics, Inc. All rights reserved.
- */
-
-/************************************************************************
- * *
- * WARNING!!! WARNING!!! WARNING!!! WARNING!!! WARNING!!! *
- * *
- * This file is created by an automated script. Any (minimal) changes *
- * made manually to this file should be made with care. *
- * *
- * MAKE ALL ADDITIONS TO THE END OF THIS FILE *
- * *
- ************************************************************************/
-
-
-#ifndef _ASM_IA64_SN_SN1_HUBIO_H
-#define _ASM_IA64_SN_SN1_HUBIO_H
-
-
-#define IIO_WID 0x00400000 /*
- * Crosstalk Widget
- * Identification This
- * register is also
- * accessible from
- * Crosstalk at
- * address 0x0.
- */
-
-
-
-#define IIO_WSTAT 0x00400008 /*
- * Crosstalk Widget
- * Status
- */
-
-
-
-#define IIO_WCR 0x00400020 /*
- * Crosstalk Widget
- * Control Register
- */
-
-
-
-#define IIO_ILAPR 0x00400100 /*
- * IO Local Access
- * Protection Register
- */
-
-
-
-#define IIO_ILAPO 0x00400108 /*
- * IO Local Access
- * Protection Override
- */
-
-
-
-#define IIO_IOWA 0x00400110 /*
- * IO Outbound Widget
- * Access
- */
-
-
-
-#define IIO_IIWA 0x00400118 /*
- * IO Inbound Widget
- * Access
- */
-
-
-
-#define IIO_IIDEM 0x00400120 /*
- * IO Inbound Device
- * Error Mask
- */
-
-
-
-#define IIO_ILCSR 0x00400128 /*
- * IO LLP Control and
- * Status Register
- */
-
-
-
-#define IIO_ILLR 0x00400130 /* IO LLP Log Register */
-
-
-
-#define IIO_IIDSR 0x00400138 /*
- * IO Interrupt
- * Destination
- */
-
-
-
-#define IIO_IGFX0 0x00400140 /*
- * IO Graphics
- * Node-Widget Map 0
- */
-
-
-
-#define IIO_IGFX1 0x00400148 /*
- * IO Graphics
- * Node-Widget Map 1
- */
-
-
-
-#define IIO_ISCR0 0x00400150 /*
- * IO Scratch Register
- * 0
- */
-
-
-
-#define IIO_ISCR1 0x00400158 /*
- * IO Scratch Register
- * 1
- */
-
-
-
-#define IIO_ITTE1 0x00400160 /*
- * IO Translation
- * Table Entry 1
- */
-
-
-
-#define IIO_ITTE2 0x00400168 /*
- * IO Translation
- * Table Entry 2
- */
-
-
-
-#define IIO_ITTE3 0x00400170 /*
- * IO Translation
- * Table Entry 3
- */
-
-
-
-#define IIO_ITTE4 0x00400178 /*
- * IO Translation
- * Table Entry 4
- */
-
-
-
-#define IIO_ITTE5 0x00400180 /*
- * IO Translation
- * Table Entry 5
- */
-
-
-
-#define IIO_ITTE6 0x00400188 /*
- * IO Translation
- * Table Entry 6
- */
-
-
-
-#define IIO_ITTE7 0x00400190 /*
- * IO Translation
- * Table Entry 7
- */
-
-
-
-#define IIO_IPRB0 0x00400198 /* IO PRB Entry 0 */
-
-
-
-#define IIO_IPRB8 0x004001A0 /* IO PRB Entry 8 */
-
-
-
-#define IIO_IPRB9 0x004001A8 /* IO PRB Entry 9 */
-
-
-
-#define IIO_IPRBA 0x004001B0 /* IO PRB Entry A */
-
-
-
-#define IIO_IPRBB 0x004001B8 /* IO PRB Entry B */
-
-
-
-#define IIO_IPRBC 0x004001C0 /* IO PRB Entry C */
-
-
-
-#define IIO_IPRBD 0x004001C8 /* IO PRB Entry D */
-
-
-
-#define IIO_IPRBE 0x004001D0 /* IO PRB Entry E */
-
-
-
-#define IIO_IPRBF 0x004001D8 /* IO PRB Entry F */
-
-
-
-#define IIO_IXCC 0x004001E0 /*
- * IO Crosstalk Credit
- * Count Timeout
- */
-
-
-
-#define IIO_IMEM 0x004001E8 /*
- * IO Miscellaneous
- * Error Mask
- */
-
-
-
-#define IIO_IXTT 0x004001F0 /*
- * IO Crosstalk
- * Timeout Threshold
- */
-
-
-
-#define IIO_IECLR 0x004001F8 /*
- * IO Error Clear
- * Register
- */
-
-
-
-#define IIO_IBCR 0x00400200 /*
- * IO BTE Control
- * Register
- */
-
-
-
-#define IIO_IXSM 0x00400208 /*
- * IO Crosstalk
- * Spurious Message
- */
-
-
-
-#define IIO_IXSS 0x00400210 /*
- * IO Crosstalk
- * Spurious Sideband
- */
-
-
-
-#define IIO_ILCT 0x00400218 /* IO LLP Channel Test */
-
-
-
-#define IIO_IIEPH1 0x00400220 /*
- * IO Incoming Error
- * Packet Header, Part
- * 1
- */
-
-
-
-#define IIO_IIEPH2 0x00400228 /*
- * IO Incoming Error
- * Packet Header, Part
- * 2
- */
-
-
-
-#define IIO_IPCA 0x00400300 /*
- * IO PRB Counter
- * Adjust
- */
-
-
-
-#define IIO_IPRTE0 0x00400308 /*
- * IO PIO Read Address
- * Table Entry 0
- */
-
-
-
-#define IIO_IPRTE1 0x00400310 /*
- * IO PIO Read Address
- * Table Entry 1
- */
-
-
-
-#define IIO_IPRTE2 0x00400318 /*
- * IO PIO Read Address
- * Table Entry 2
- */
-
-
-
-#define IIO_IPRTE3 0x00400320 /*
- * IO PIO Read Address
- * Table Entry 3
- */
-
-
-
-#define IIO_IPRTE4 0x00400328 /*
- * IO PIO Read Address
- * Table Entry 4
- */
-
-
-
-#define IIO_IPRTE5 0x00400330 /*
- * IO PIO Read Address
- * Table Entry 5
- */
-
-
-
-#define IIO_IPRTE6 0x00400338 /*
- * IO PIO Read Address
- * Table Entry 6
- */
-
-
-
-#define IIO_IPRTE7 0x00400340 /*
- * IO PIO Read Address
- * Table Entry 7
- */
-
-
-
-#define IIO_IPDR 0x00400388 /*
- * IO PIO Deallocation
- * Register
- */
-
-
-
-#define IIO_ICDR 0x00400390 /*
- * IO CRB Entry
- * Deallocation
- * Register
- */
-
-
-
-#define IIO_IFDR 0x00400398 /*
- * IO IOQ FIFO Depth
- * Register
- */
-
-
-
-#define IIO_IIAP 0x004003A0 /*
- * IO IIQ Arbitration
- * Parameters
- */
-
-
-
-#define IIO_ICMR 0x004003A8 /*
- * IO CRB Management
- * Register
- */
-
-
-
-#define IIO_ICCR 0x004003B0 /*
- * IO CRB Control
- * Register
- */
-
-
-
-#define IIO_ICTO 0x004003B8 /* IO CRB Timeout */
-
-
-
-#define IIO_ICTP 0x004003C0 /*
- * IO CRB Timeout
- * Prescalar
- */
-
-
-
-#define IIO_ICRB0_A 0x00400400 /* IO CRB Entry 0_A */
-
-
-
-#define IIO_ICRB0_B 0x00400408 /* IO CRB Entry 0_B */
-
-
-
-#define IIO_ICRB0_C 0x00400410 /* IO CRB Entry 0_C */
-
-
-
-#define IIO_ICRB0_D 0x00400418 /* IO CRB Entry 0_D */
-
-
-
-#define IIO_ICRB1_A 0x00400420 /* IO CRB Entry 1_A */
-
-
-
-#define IIO_ICRB1_B 0x00400428 /* IO CRB Entry 1_B */
-
-
-
-#define IIO_ICRB1_C 0x00400430 /* IO CRB Entry 1_C */
-
-
-
-#define IIO_ICRB1_D 0x00400438 /* IO CRB Entry 1_D */
-
-
-
-#define IIO_ICRB2_A 0x00400440 /* IO CRB Entry 2_A */
-
-
-
-#define IIO_ICRB2_B 0x00400448 /* IO CRB Entry 2_B */
-
-
-
-#define IIO_ICRB2_C 0x00400450 /* IO CRB Entry 2_C */
-
-
-
-#define IIO_ICRB2_D 0x00400458 /* IO CRB Entry 2_D */
-
-
-
-#define IIO_ICRB3_A 0x00400460 /* IO CRB Entry 3_A */
-
-
-
-#define IIO_ICRB3_B 0x00400468 /* IO CRB Entry 3_B */
-
-
-
-#define IIO_ICRB3_C 0x00400470 /* IO CRB Entry 3_C */
-
-
-
-#define IIO_ICRB3_D 0x00400478 /* IO CRB Entry 3_D */
-
-
-
-#define IIO_ICRB4_A 0x00400480 /* IO CRB Entry 4_A */
-
-
-
-#define IIO_ICRB4_B 0x00400488 /* IO CRB Entry 4_B */
-
-
-
-#define IIO_ICRB4_C 0x00400490 /* IO CRB Entry 4_C */
-
-
-
-#define IIO_ICRB4_D 0x00400498 /* IO CRB Entry 4_D */
-
-
-
-#define IIO_ICRB5_A 0x004004A0 /* IO CRB Entry 5_A */
-
-
-
-#define IIO_ICRB5_B 0x004004A8 /* IO CRB Entry 5_B */
-
-
-
-#define IIO_ICRB5_C 0x004004B0 /* IO CRB Entry 5_C */
-
-
-
-#define IIO_ICRB5_D 0x004004B8 /* IO CRB Entry 5_D */
-
-
-
-#define IIO_ICRB6_A 0x004004C0 /* IO CRB Entry 6_A */
-
-
-
-#define IIO_ICRB6_B 0x004004C8 /* IO CRB Entry 6_B */
-
-
-
-#define IIO_ICRB6_C 0x004004D0 /* IO CRB Entry 6_C */
-
-
-
-#define IIO_ICRB6_D 0x004004D8 /* IO CRB Entry 6_D */
-
-
-
-#define IIO_ICRB7_A 0x004004E0 /* IO CRB Entry 7_A */
-
-
-
-#define IIO_ICRB7_B 0x004004E8 /* IO CRB Entry 7_B */
-
-
-
-#define IIO_ICRB7_C 0x004004F0 /* IO CRB Entry 7_C */
-
-
-
-#define IIO_ICRB7_D 0x004004F8 /* IO CRB Entry 7_D */
-
-
-
-#define IIO_ICRB8_A 0x00400500 /* IO CRB Entry 8_A */
-
-
-
-#define IIO_ICRB8_B 0x00400508 /* IO CRB Entry 8_B */
-
-
-
-#define IIO_ICRB8_C 0x00400510 /* IO CRB Entry 8_C */
-
-
-
-#define IIO_ICRB8_D 0x00400518 /* IO CRB Entry 8_D */
-
-
-
-#define IIO_ICRB9_A 0x00400520 /* IO CRB Entry 9_A */
-
-
-
-#define IIO_ICRB9_B 0x00400528 /* IO CRB Entry 9_B */
-
-
-
-#define IIO_ICRB9_C 0x00400530 /* IO CRB Entry 9_C */
-
-
-
-#define IIO_ICRB9_D 0x00400538 /* IO CRB Entry 9_D */
-
-
-
-#define IIO_ICRBA_A 0x00400540 /* IO CRB Entry A_A */
-
-
-
-#define IIO_ICRBA_B 0x00400548 /* IO CRB Entry A_B */
-
-
-
-#define IIO_ICRBA_C 0x00400550 /* IO CRB Entry A_C */
-
-
-
-#define IIO_ICRBA_D 0x00400558 /* IO CRB Entry A_D */
-
-
-
-#define IIO_ICRBB_A 0x00400560 /* IO CRB Entry B_A */
-
-
-
-#define IIO_ICRBB_B 0x00400568 /* IO CRB Entry B_B */
-
-
-
-#define IIO_ICRBB_C 0x00400570 /* IO CRB Entry B_C */
-
-
-
-#define IIO_ICRBB_D 0x00400578 /* IO CRB Entry B_D */
-
-
-
-#define IIO_ICRBC_A 0x00400580 /* IO CRB Entry C_A */
-
-
-
-#define IIO_ICRBC_B 0x00400588 /* IO CRB Entry C_B */
-
-
-
-#define IIO_ICRBC_C 0x00400590 /* IO CRB Entry C_C */
-
-
-
-#define IIO_ICRBC_D 0x00400598 /* IO CRB Entry C_D */
-
-
-
-#define IIO_ICRBD_A 0x004005A0 /* IO CRB Entry D_A */
-
-
-
-#define IIO_ICRBD_B 0x004005A8 /* IO CRB Entry D_B */
-
-
-
-#define IIO_ICRBD_C 0x004005B0 /* IO CRB Entry D_C */
-
-
-
-#define IIO_ICRBD_D 0x004005B8 /* IO CRB Entry D_D */
-
-
-
-#define IIO_ICRBE_A 0x004005C0 /* IO CRB Entry E_A */
-
-
-
-#define IIO_ICRBE_B 0x004005C8 /* IO CRB Entry E_B */
-
-
-
-#define IIO_ICRBE_C 0x004005D0 /* IO CRB Entry E_C */
-
-
-
-#define IIO_ICRBE_D 0x004005D8 /* IO CRB Entry E_D */
-
-
-
-#define IIO_ICSML 0x00400600 /*
- * IO CRB Spurious
- * Message Low
- */
-
-
-
-#define IIO_ICSMH 0x00400608 /*
- * IO CRB Spurious
- * Message High
- */
-
-
-
-#define IIO_IDBSS 0x00400610 /*
- * IO Debug Submenu
- * Select
- */
-
-
-
-#define IIO_IBLS0 0x00410000 /*
- * IO BTE Length
- * Status 0
- */
-
-
-
-#define IIO_IBSA0 0x00410008 /*
- * IO BTE Source
- * Address 0
- */
-
-
-
-#define IIO_IBDA0 0x00410010 /*
- * IO BTE Destination
- * Address 0
- */
-
-
-
-#define IIO_IBCT0 0x00410018 /*
- * IO BTE Control
- * Terminate 0
- */
-
-
-
-#define IIO_IBNA0 0x00410020 /*
- * IO BTE Notification
- * Address 0
- */
-
-
-
-#define IIO_IBIA0 0x00410028 /*
- * IO BTE Interrupt
- * Address 0
- */
-
-
-
-#define IIO_IBLS1 0x00420000 /*
- * IO BTE Length
- * Status 1
- */
-
-
-
-#define IIO_IBSA1 0x00420008 /*
- * IO BTE Source
- * Address 1
- */
-
-
-
-#define IIO_IBDA1 0x00420010 /*
- * IO BTE Destination
- * Address 1
- */
-
-
-
-#define IIO_IBCT1 0x00420018 /*
- * IO BTE Control
- * Terminate 1
- */
-
-
-
-#define IIO_IBNA1 0x00420020 /*
- * IO BTE Notification
- * Address 1
- */
-
-
-
-#define IIO_IBIA1 0x00420028 /*
- * IO BTE Interrupt
- * Address 1
- */
-
-
-
-#define IIO_IPCR 0x00430000 /*
- * IO Performance
- * Control
- */
-
-
-
-#define IIO_IPPR 0x00430008 /*
- * IO Performance
- * Profiling
- */
-
-
-
-
-
-#ifndef __ASSEMBLY__
-
-/************************************************************************
- * *
- * Description: This register echoes some information from the *
- * LB_REV_ID register. It is available through Crosstalk as described *
- * above. The REV_NUM and MFG_NUM fields receive their values from *
- * the REVISION and MANUFACTURER fields in the LB_REV_ID register. *
- * The PART_NUM field's value is the Crosstalk device ID number that *
- * Steve Miller assigned to the Bedrock chip. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_wid_u {
- bdrkreg_t ii_wid_regval;
- struct {
- bdrkreg_t w_rsvd_1 : 1;
- bdrkreg_t w_mfg_num : 11;
- bdrkreg_t w_part_num : 16;
- bdrkreg_t w_rev_num : 4;
- bdrkreg_t w_rsvd : 32;
- } ii_wid_fld_s;
-} ii_wid_u_t;
-
-#else
-
-typedef union ii_wid_u {
- bdrkreg_t ii_wid_regval;
- struct {
- bdrkreg_t w_rsvd : 32;
- bdrkreg_t w_rev_num : 4;
- bdrkreg_t w_part_num : 16;
- bdrkreg_t w_mfg_num : 11;
- bdrkreg_t w_rsvd_1 : 1;
- } ii_wid_fld_s;
-} ii_wid_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * The fields in this register are set upon detection of an error *
- * and cleared by various mechanisms, as explained in the *
- * description. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_wstat_u {
- bdrkreg_t ii_wstat_regval;
- struct {
- bdrkreg_t w_pending : 4;
- bdrkreg_t w_xt_crd_to : 1;
- bdrkreg_t w_xt_tail_to : 1;
- bdrkreg_t w_rsvd_3 : 3;
- bdrkreg_t w_tx_mx_rty : 1;
- bdrkreg_t w_rsvd_2 : 6;
- bdrkreg_t w_llp_tx_cnt : 8;
- bdrkreg_t w_rsvd_1 : 8;
- bdrkreg_t w_crazy : 1;
- bdrkreg_t w_rsvd : 31;
- } ii_wstat_fld_s;
-} ii_wstat_u_t;
-
-#else
-
-typedef union ii_wstat_u {
- bdrkreg_t ii_wstat_regval;
- struct {
- bdrkreg_t w_rsvd : 31;
- bdrkreg_t w_crazy : 1;
- bdrkreg_t w_rsvd_1 : 8;
- bdrkreg_t w_llp_tx_cnt : 8;
- bdrkreg_t w_rsvd_2 : 6;
- bdrkreg_t w_tx_mx_rty : 1;
- bdrkreg_t w_rsvd_3 : 3;
- bdrkreg_t w_xt_tail_to : 1;
- bdrkreg_t w_xt_crd_to : 1;
- bdrkreg_t w_pending : 4;
- } ii_wstat_fld_s;
-} ii_wstat_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This is a read-write enabled register. It controls *
- * various aspects of the Crosstalk flow control. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_wcr_u {
- bdrkreg_t ii_wcr_regval;
- struct {
- bdrkreg_t w_wid : 4;
- bdrkreg_t w_tag : 1;
- bdrkreg_t w_rsvd_1 : 8;
- bdrkreg_t w_dst_crd : 3;
- bdrkreg_t w_f_bad_pkt : 1;
- bdrkreg_t w_dir_con : 1;
- bdrkreg_t w_e_thresh : 5;
- bdrkreg_t w_rsvd : 41;
- } ii_wcr_fld_s;
-} ii_wcr_u_t;
-
-#else
-
-typedef union ii_wcr_u {
- bdrkreg_t ii_wcr_regval;
- struct {
- bdrkreg_t w_rsvd : 41;
- bdrkreg_t w_e_thresh : 5;
- bdrkreg_t w_dir_con : 1;
- bdrkreg_t w_f_bad_pkt : 1;
- bdrkreg_t w_dst_crd : 3;
- bdrkreg_t w_rsvd_1 : 8;
- bdrkreg_t w_tag : 1;
- bdrkreg_t w_wid : 4;
- } ii_wcr_fld_s;
-} ii_wcr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This register's value is a bit vector that guards *
- * access to local registers within the II as well as to external *
- * Crosstalk widgets. Each bit in the register corresponds to a *
- * particular region in the system; a region consists of one, two or *
- * four nodes (depending on the value of the REGION_SIZE field in the *
- * LB_REV_ID register, which is documented in Section 8.3.1.1). The *
- * protection provided by this register applies to PIO read *
- * operations as well as PIO write operations. The II will perform a *
- * PIO read or write request only if the bit for the requestor's *
- * region is set; otherwise, the II will not perform the requested *
- * operation and will return an error response. When a PIO read or *
- * write request targets an external Crosstalk widget, then not only *
- * must the bit for the requestor's region be set in the ILAPR, but *
- * also the target widget's bit in the IOWA register must be set in *
- * order for the II to perform the requested operation; otherwise, *
- * the II will return an error response. Hence, the protection *
- * provided by the IOWA register supplements the protection provided *
- * by the ILAPR for requests that target external Crosstalk widgets. *
- * This register itself can be accessed only by the nodes whose *
- * region ID bits are enabled in this same register. It can also be *
- * accessed through the IAlias space by the local processors. *
- * The reset value of this register allows access by all nodes. *
- * *
- ************************************************************************/
-
-
-
-
-typedef union ii_ilapr_u {
- bdrkreg_t ii_ilapr_regval;
- struct {
- bdrkreg_t i_region : 64;
- } ii_ilapr_fld_s;
-} ii_ilapr_u_t;
-
-
-
-
-/************************************************************************
- * *
- * Description: A write to this register of the 64-bit value *
- * "SGIrules" in ASCII, will cause the bit in the ILAPR register *
- * corresponding to the region of the requestor to be set (allow *
- * access). A write of any other value will be ignored. Access *
- * protection for this register is "SGIrules". *
- * This register can also be accessed through the IAlias space. *
- * However, this access will not change the access permissions in the *
- * ILAPR. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ilapo_u {
- bdrkreg_t ii_ilapo_regval;
- struct {
- bdrkreg_t i_io_ovrride : 9;
- bdrkreg_t i_rsvd : 55;
- } ii_ilapo_fld_s;
-} ii_ilapo_u_t;
-
-#else
-
-typedef union ii_ilapo_u {
- bdrkreg_t ii_ilapo_regval;
- struct {
- bdrkreg_t i_rsvd : 55;
- bdrkreg_t i_io_ovrride : 9;
- } ii_ilapo_fld_s;
-} ii_ilapo_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register qualifies all the PIO and Graphics writes launched *
- * from the Bedrock towards a widget. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iowa_u {
- bdrkreg_t ii_iowa_regval;
- struct {
- bdrkreg_t i_w0_oac : 1;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_wx_oac : 8;
- bdrkreg_t i_rsvd : 48;
- } ii_iowa_fld_s;
-} ii_iowa_u_t;
-
-#else
-
-typedef union ii_iowa_u {
- bdrkreg_t ii_iowa_regval;
- struct {
- bdrkreg_t i_rsvd : 48;
- bdrkreg_t i_wx_oac : 8;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_w0_oac : 1;
- } ii_iowa_fld_s;
-} ii_iowa_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This register qualifies all the requests launched *
- * from a widget towards the Bedrock. This register is intended to be *
- * used by software in case of misbehaving widgets. *
- * *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iiwa_u {
- bdrkreg_t ii_iiwa_regval;
- struct {
- bdrkreg_t i_w0_iac : 1;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_wx_iac : 8;
- bdrkreg_t i_rsvd : 48;
- } ii_iiwa_fld_s;
-} ii_iiwa_u_t;
-
-#else
-
-typedef union ii_iiwa_u {
- bdrkreg_t ii_iiwa_regval;
- struct {
- bdrkreg_t i_rsvd : 48;
- bdrkreg_t i_wx_iac : 8;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_w0_iac : 1;
- } ii_iiwa_fld_s;
-} ii_iiwa_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This register qualifies all the operations launched *
- * from a widget towards the Bedrock. It allows individual access *
- * control for up to 8 devices per widget. A device refers to *
- * individual DMA master hosted by a widget. *
- * The bits in each field of this register are cleared by the Bedrock *
- * upon detection of an error which requires the device to be *
- * disabled. These fields assume that 0=TNUM=7 (i.e., Bridge-centric *
- * Crosstalk). Whether or not a device has access rights to this *
- * Bedrock is determined by an AND of the device enable bit in the *
- * appropriate field of this register and the corresponding bit in *
- * the Wx_IAC field (for the widget which this device belongs to). *
- * The bits in this field are set by writing a 1 to them. Incoming *
- * replies from Crosstalk are not subject to this access control *
- * mechanism. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iidem_u {
- bdrkreg_t ii_iidem_regval;
- struct {
- bdrkreg_t i_w8_dxs : 8;
- bdrkreg_t i_w9_dxs : 8;
- bdrkreg_t i_wa_dxs : 8;
- bdrkreg_t i_wb_dxs : 8;
- bdrkreg_t i_wc_dxs : 8;
- bdrkreg_t i_wd_dxs : 8;
- bdrkreg_t i_we_dxs : 8;
- bdrkreg_t i_wf_dxs : 8;
- } ii_iidem_fld_s;
-} ii_iidem_u_t;
-
-#else
-
-typedef union ii_iidem_u {
- bdrkreg_t ii_iidem_regval;
- struct {
- bdrkreg_t i_wf_dxs : 8;
- bdrkreg_t i_we_dxs : 8;
- bdrkreg_t i_wd_dxs : 8;
- bdrkreg_t i_wc_dxs : 8;
- bdrkreg_t i_wb_dxs : 8;
- bdrkreg_t i_wa_dxs : 8;
- bdrkreg_t i_w9_dxs : 8;
- bdrkreg_t i_w8_dxs : 8;
- } ii_iidem_fld_s;
-} ii_iidem_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the various programmable fields necessary *
- * for controlling and observing the LLP signals. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ilcsr_u {
- bdrkreg_t ii_ilcsr_regval;
- struct {
- bdrkreg_t i_nullto : 6;
- bdrkreg_t i_rsvd_4 : 2;
- bdrkreg_t i_wrmrst : 1;
- bdrkreg_t i_rsvd_3 : 1;
- bdrkreg_t i_llp_en : 1;
- bdrkreg_t i_bm8 : 1;
- bdrkreg_t i_llp_stat : 2;
- bdrkreg_t i_remote_power : 1;
- bdrkreg_t i_rsvd_2 : 1;
- bdrkreg_t i_maxrtry : 10;
- bdrkreg_t i_d_avail_sel : 2;
- bdrkreg_t i_rsvd_1 : 4;
- bdrkreg_t i_maxbrst : 10;
- bdrkreg_t i_rsvd : 22;
-
- } ii_ilcsr_fld_s;
-} ii_ilcsr_u_t;
-
-#else
-
-typedef union ii_ilcsr_u {
- bdrkreg_t ii_ilcsr_regval;
- struct {
- bdrkreg_t i_rsvd : 22;
- bdrkreg_t i_maxbrst : 10;
- bdrkreg_t i_rsvd_1 : 4;
- bdrkreg_t i_d_avail_sel : 2;
- bdrkreg_t i_maxrtry : 10;
- bdrkreg_t i_rsvd_2 : 1;
- bdrkreg_t i_remote_power : 1;
- bdrkreg_t i_llp_stat : 2;
- bdrkreg_t i_bm8 : 1;
- bdrkreg_t i_llp_en : 1;
- bdrkreg_t i_rsvd_3 : 1;
- bdrkreg_t i_wrmrst : 1;
- bdrkreg_t i_rsvd_4 : 2;
- bdrkreg_t i_nullto : 6;
- } ii_ilcsr_fld_s;
-} ii_ilcsr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This is simply a status registers that monitors the LLP error *
- * rate. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_illr_u {
- bdrkreg_t ii_illr_regval;
- struct {
- bdrkreg_t i_sn_cnt : 16;
- bdrkreg_t i_cb_cnt : 16;
- bdrkreg_t i_rsvd : 32;
- } ii_illr_fld_s;
-} ii_illr_u_t;
-
-#else
-
-typedef union ii_illr_u {
- bdrkreg_t ii_illr_regval;
- struct {
- bdrkreg_t i_rsvd : 32;
- bdrkreg_t i_cb_cnt : 16;
- bdrkreg_t i_sn_cnt : 16;
- } ii_illr_fld_s;
-} ii_illr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: All II-detected non-BTE error interrupts are *
- * specified via this register. *
- * NOTE: The PI interrupt register address is hardcoded in the II. If *
- * PI_ID==0, then the II sends an interrupt request (Duplonet PWRI *
- * packet) to address offset 0x0180_0090 within the local register *
- * address space of PI0 on the node specified by the NODE field. If *
- * PI_ID==1, then the II sends the interrupt request to address *
- * offset 0x01A0_0090 within the local register address space of PI1 *
- * on the node specified by the NODE field. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iidsr_u {
- bdrkreg_t ii_iidsr_regval;
- struct {
- bdrkreg_t i_level : 7;
- bdrkreg_t i_rsvd_4 : 1;
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_node : 8;
- bdrkreg_t i_rsvd_3 : 7;
- bdrkreg_t i_enable : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_int_sent : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_pi0_forward_int : 1;
- bdrkreg_t i_pi1_forward_int : 1;
- bdrkreg_t i_rsvd : 30;
- } ii_iidsr_fld_s;
-} ii_iidsr_u_t;
-
-#else
-
-typedef union ii_iidsr_u {
- bdrkreg_t ii_iidsr_regval;
- struct {
- bdrkreg_t i_rsvd : 30;
- bdrkreg_t i_pi1_forward_int : 1;
- bdrkreg_t i_pi0_forward_int : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_int_sent : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_enable : 1;
- bdrkreg_t i_rsvd_3 : 7;
- bdrkreg_t i_node : 8;
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_rsvd_4 : 1;
- bdrkreg_t i_level : 7;
- } ii_iidsr_fld_s;
-} ii_iidsr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are two instances of this register. This register is used *
- * for matching up the incoming responses from the graphics widget to *
- * the processor that initiated the graphics operation. The *
- * write-responses are converted to graphics credits and returned to *
- * the processor so that the processor interface can manage the flow *
- * control. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_igfx0_u {
- bdrkreg_t ii_igfx0_regval;
- struct {
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_n_num : 8;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_p_num : 1;
- bdrkreg_t i_rsvd : 47;
- } ii_igfx0_fld_s;
-} ii_igfx0_u_t;
-
-#else
-
-typedef union ii_igfx0_u {
- bdrkreg_t ii_igfx0_regval;
- struct {
- bdrkreg_t i_rsvd : 47;
- bdrkreg_t i_p_num : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_n_num : 8;
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_w_num : 4;
- } ii_igfx0_fld_s;
-} ii_igfx0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are two instances of this register. This register is used *
- * for matching up the incoming responses from the graphics widget to *
- * the processor that initiated the graphics operation. The *
- * write-responses are converted to graphics credits and returned to *
- * the processor so that the processor interface can manage the flow *
- * control. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_igfx1_u {
- bdrkreg_t ii_igfx1_regval;
- struct {
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_n_num : 8;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_p_num : 1;
- bdrkreg_t i_rsvd : 47;
- } ii_igfx1_fld_s;
-} ii_igfx1_u_t;
-
-#else
-
-typedef union ii_igfx1_u {
- bdrkreg_t ii_igfx1_regval;
- struct {
- bdrkreg_t i_rsvd : 47;
- bdrkreg_t i_p_num : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_n_num : 8;
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_w_num : 4;
- } ii_igfx1_fld_s;
-} ii_igfx1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are two instances of this registers. These registers are *
- * used as scratch registers for software use. *
- * *
- ************************************************************************/
-
-
-
-
-typedef union ii_iscr0_u {
- bdrkreg_t ii_iscr0_regval;
- struct {
- bdrkreg_t i_scratch : 64;
- } ii_iscr0_fld_s;
-} ii_iscr0_u_t;
-
-
-
-
-/************************************************************************
- * *
- * There are two instances of this registers. These registers are *
- * used as scratch registers for software use. *
- * *
- ************************************************************************/
-
-
-
-
-typedef union ii_iscr1_u {
- bdrkreg_t ii_iscr1_regval;
- struct {
- bdrkreg_t i_scratch : 64;
- } ii_iscr1_fld_s;
-} ii_iscr1_u_t;
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte1_u {
- bdrkreg_t ii_itte1_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte1_fld_s;
-} ii_itte1_u_t;
-
-#else
-
-typedef union ii_itte1_u {
- bdrkreg_t ii_itte1_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte1_fld_s;
-} ii_itte1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte2_u {
- bdrkreg_t ii_itte2_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte2_fld_s;
-} ii_itte2_u_t;
-
-#else
-typedef union ii_itte2_u {
- bdrkreg_t ii_itte2_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte2_fld_s;
-} ii_itte2_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte3_u {
- bdrkreg_t ii_itte3_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte3_fld_s;
-} ii_itte3_u_t;
-
-#else
-
-typedef union ii_itte3_u {
- bdrkreg_t ii_itte3_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte3_fld_s;
-} ii_itte3_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte4_u {
- bdrkreg_t ii_itte4_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte4_fld_s;
-} ii_itte4_u_t;
-
-#else
-
-typedef union ii_itte4_u {
- bdrkreg_t ii_itte4_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte4_fld_s;
-} ii_itte4_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte5_u {
- bdrkreg_t ii_itte5_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte5_fld_s;
-} ii_itte5_u_t;
-
-#else
-
-typedef union ii_itte5_u {
- bdrkreg_t ii_itte5_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte5_fld_s;
-} ii_itte5_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte6_u {
- bdrkreg_t ii_itte6_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte6_fld_s;
-} ii_itte6_u_t;
-
-#else
-
-typedef union ii_itte6_u {
- bdrkreg_t ii_itte6_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte6_fld_s;
-} ii_itte6_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are seven instances of translation table entry *
- * registers. Each register maps a Bedrock Big Window to a 48-bit *
- * address on Crosstalk. *
- * For M-mode (128 nodes, 8 GBytes/node), SysAD[31:29] (Big Window *
- * number) are used to select one of these 7 registers. The Widget *
- * number field is then derived from the W_NUM field for synthesizing *
- * a Crosstalk packet. The 5 bits of OFFSET are concatenated with *
- * SysAD[28:0] to form Crosstalk[33:0]. The upper Crosstalk[47:34] *
- * are padded with zeros. Although the maximum Crosstalk space *
- * addressable by the Bedrock is thus the lower 16 GBytes per widget *
- * (M-mode), however only <SUP >7</SUP>/<SUB >32nds</SUB> of this *
- * space can be accessed. *
- * For the N-mode (256 nodes, 4 GBytes/node), SysAD[30:28] (Big *
- * Window number) are used to select one of these 7 registers. The *
- * Widget number field is then derived from the W_NUM field for *
- * synthesizing a Crosstalk packet. The 5 bits of OFFSET are *
- * concatenated with SysAD[27:0] to form Crosstalk[33:0]. The IOSP *
- * field is used as Crosstalk[47], and remainder of the Crosstalk *
- * address bits (Crosstalk[46:34]) are always zero. While the maximum *
- * Crosstalk space addressable by the Bedrock is thus the lower *
- * 8-GBytes per widget (N-mode), only <SUP >7</SUP>/<SUB >32nds</SUB> *
- * of this space can be accessed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_itte7_u {
- bdrkreg_t ii_itte7_regval;
- struct {
- bdrkreg_t i_offset : 5;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_itte7_fld_s;
-} ii_itte7_u_t;
-
-#else
-
-typedef union ii_itte7_u {
- bdrkreg_t ii_itte7_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_iosp : 1;
- bdrkreg_t i_w_num : 4;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_offset : 5;
- } ii_itte7_fld_s;
-} ii_itte7_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprb0_u {
- bdrkreg_t ii_iprb0_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprb0_fld_s;
-} ii_iprb0_u_t;
-
-#else
-
-typedef union ii_iprb0_u {
- bdrkreg_t ii_iprb0_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprb0_fld_s;
-} ii_iprb0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprb8_u {
- bdrkreg_t ii_iprb8_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprb8_fld_s;
-} ii_iprb8_u_t;
-
-#else
-
-
-typedef union ii_iprb8_u {
- bdrkreg_t ii_iprb8_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprb8_fld_s;
-} ii_iprb8_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprb9_u {
- bdrkreg_t ii_iprb9_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprb9_fld_s;
-} ii_iprb9_u_t;
-
-#else
-
-typedef union ii_iprb9_u {
- bdrkreg_t ii_iprb9_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprb9_fld_s;
-} ii_iprb9_u_t;
-
-#endif
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprba_u {
- bdrkreg_t ii_iprba_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprba_fld_s;
-} ii_iprba_u_t;
-
-#else
-
-typedef union ii_iprba_u {
- bdrkreg_t ii_iprba_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprba_fld_s;
-} ii_iprba_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprbb_u {
- bdrkreg_t ii_iprbb_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprbb_fld_s;
-} ii_iprbb_u_t;
-
-#else
-
-typedef union ii_iprbb_u {
- bdrkreg_t ii_iprbb_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprbb_fld_s;
-} ii_iprbb_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprbc_u {
- bdrkreg_t ii_iprbc_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprbc_fld_s;
-} ii_iprbc_u_t;
-
-#else
-
-typedef union ii_iprbc_u {
- bdrkreg_t ii_iprbc_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprbc_fld_s;
-} ii_iprbc_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprbd_u {
- bdrkreg_t ii_iprbd_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprbd_fld_s;
-} ii_iprbd_u_t;
-
-#else
-
-typedef union ii_iprbd_u {
- bdrkreg_t ii_iprbd_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprbd_fld_s;
-} ii_iprbd_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprbe_u {
- bdrkreg_t ii_iprbe_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprbe_fld_s;
-} ii_iprbe_u_t;
-
-#else
-
-typedef union ii_iprbe_u {
- bdrkreg_t ii_iprbe_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprbe_fld_s;
-} ii_iprbe_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 9 instances of this register, one per *
- * actual widget in this implementation of Bedrock and Crossbow. *
- * Note: Crossbow only has ports for Widgets 8 through F, widget 0 *
- * refers to Crossbow's internal space. *
- * This register contains the state elements per widget that are *
- * necessary to manage the PIO flow control on Crosstalk and on the *
- * Router Network. See the PIO Flow Control chapter for a complete *
- * description of this register *
- * The SPUR_WR bit requires some explanation. When this register is *
- * written, the new value of the C field is captured in an internal *
- * register so the hardware can remember what the programmer wrote *
- * into the credit counter. The SPUR_WR bit sets whenever the C field *
- * increments above this stored value, which indicates that there *
- * have been more responses received than requests sent. The SPUR_WR *
- * bit cannot be cleared until a value is written to the IPRBx *
- * register; the write will correct the C field and capture its new *
- * value in the internal register. Even if IECLR[E_PRB_x] is set, the *
- * SPUR_WR bit will persist if IPRBx hasn't yet been written. *
- * . *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprbf_u {
- bdrkreg_t ii_iprbf_regval;
- struct {
- bdrkreg_t i_c : 8;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_mult_err : 1;
- } ii_iprbe_fld_s;
-} ii_iprbf_u_t;
-
-#else
-
-typedef union ii_iprbf_u {
- bdrkreg_t ii_iprbf_regval;
- struct {
- bdrkreg_t i_mult_err : 1;
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_spur_rd : 1;
- bdrkreg_t i_spur_wr : 1;
- bdrkreg_t i_rd_to : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_of_cnt : 5;
- bdrkreg_t i_f : 1;
- bdrkreg_t i_m : 2;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_nb : 14;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_na : 14;
- bdrkreg_t i_c : 8;
- } ii_iprbf_fld_s;
-} ii_iprbf_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register specifies the timeout value to use for monitoring *
- * Crosstalk credits which are used outbound to Crosstalk. An *
- * internal counter called the Crosstalk Credit Timeout Counter *
- * increments every 128 II clocks. The counter starts counting *
- * anytime the credit count drops below a threshold, and resets to *
- * zero (stops counting) anytime the credit count is at or above the *
- * threshold. The threshold is 1 credit in direct connect mode and 2 *
- * in Crossbow connect mode. When the internal Crosstalk Credit *
- * Timeout Counter reaches the value programmed in this register, a *
- * Crosstalk Credit Timeout has occurred. The internal counter is not *
- * readable from software, and stops counting at its maximum value, *
- * so it cannot cause more than one interrupt. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ixcc_u {
- bdrkreg_t ii_ixcc_regval;
- struct {
- bdrkreg_t i_time_out : 26;
- bdrkreg_t i_rsvd : 38;
- } ii_ixcc_fld_s;
-} ii_ixcc_u_t;
-
-#else
-
-typedef union ii_ixcc_u {
- bdrkreg_t ii_ixcc_regval;
- struct {
- bdrkreg_t i_rsvd : 38;
- bdrkreg_t i_time_out : 26;
- } ii_ixcc_fld_s;
-} ii_ixcc_u_t;
-
-#endif
-
-
-
-/************************************************************************
- * *
- * Description: This register qualifies all the PIO and DMA *
- * operations launched from widget 0 towards the Bedrock. In *
- * addition, it also qualifies accesses by the BTE streams. *
- * The bits in each field of this register are cleared by the Bedrock *
- * upon detection of an error which requires widget 0 or the BTE *
- * streams to be terminated. Whether or not widget x has access *
- * rights to this Bedrock is determined by an AND of the device *
- * enable bit in the appropriate field of this register and bit 0 in *
- * the Wx_IAC field. The bits in this field are set by writing a 1 to *
- * them. Incoming replies from Crosstalk are not subject to this *
- * access control mechanism. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_imem_u {
- bdrkreg_t ii_imem_regval;
- struct {
- bdrkreg_t i_w0_esd : 1;
- bdrkreg_t i_rsvd_3 : 3;
- bdrkreg_t i_b0_esd : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_b1_esd : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_clr_precise : 1;
- bdrkreg_t i_rsvd : 51;
- } ii_imem_fld_s;
-} ii_imem_u_t;
-
-#else
-
-typedef union ii_imem_u {
- bdrkreg_t ii_imem_regval;
- struct {
- bdrkreg_t i_rsvd : 51;
- bdrkreg_t i_clr_precise : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_b1_esd : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_b0_esd : 1;
- bdrkreg_t i_rsvd_3 : 3;
- bdrkreg_t i_w0_esd : 1;
- } ii_imem_fld_s;
-} ii_imem_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This register specifies the timeout value to use for *
- * monitoring Crosstalk tail flits coming into the Bedrock in the *
- * TAIL_TO field. An internal counter associated with this register *
- * is incremented every 128 II internal clocks (7 bits). The counter *
- * starts counting anytime a header micropacket is received and stops *
- * counting (and resets to zero) any time a micropacket with a Tail *
- * bit is received. Once the counter reaches the threshold value *
- * programmed in this register, it generates an interrupt to the *
- * processor that is programmed into the IIDSR. The counter saturates *
- * (does not roll over) at its maximum value, so it cannot cause *
- * another interrupt until after it is cleared. *
- * The register also contains the Read Response Timeout values. The *
- * Prescalar is 23 bits, and counts II clocks. An internal counter *
- * increments on every II clock and when it reaches the value in the *
- * Prescalar field, all IPRTE registers with their valid bits set *
- * have their Read Response timers bumped. Whenever any of them match *
- * the value in the RRSP_TO field, a Read Response Timeout has *
- * occurred, and error handling occurs as described in the Error *
- * Handling section of this document. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ixtt_u {
- bdrkreg_t ii_ixtt_regval;
- struct {
- bdrkreg_t i_tail_to : 26;
- bdrkreg_t i_rsvd_1 : 6;
- bdrkreg_t i_rrsp_ps : 23;
- bdrkreg_t i_rrsp_to : 5;
- bdrkreg_t i_rsvd : 4;
- } ii_ixtt_fld_s;
-} ii_ixtt_u_t;
-
-#else
-
-typedef union ii_ixtt_u {
- bdrkreg_t ii_ixtt_regval;
- struct {
- bdrkreg_t i_rsvd : 4;
- bdrkreg_t i_rrsp_to : 5;
- bdrkreg_t i_rrsp_ps : 23;
- bdrkreg_t i_rsvd_1 : 6;
- bdrkreg_t i_tail_to : 26;
- } ii_ixtt_fld_s;
-} ii_ixtt_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Writing a 1 to the fields of this register clears the appropriate *
- * error bits in other areas of Bedrock_II. Note that when the *
- * E_PRB_x bits are used to clear error bits in PRB registers, *
- * SPUR_RD and SPUR_WR may persist, because they require additional *
- * action to clear them. See the IPRBx and IXSS Register *
- * specifications. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ieclr_u {
- bdrkreg_t ii_ieclr_regval;
- struct {
- bdrkreg_t i_e_prb_0 : 1;
- bdrkreg_t i_rsvd : 7;
- bdrkreg_t i_e_prb_8 : 1;
- bdrkreg_t i_e_prb_9 : 1;
- bdrkreg_t i_e_prb_a : 1;
- bdrkreg_t i_e_prb_b : 1;
- bdrkreg_t i_e_prb_c : 1;
- bdrkreg_t i_e_prb_d : 1;
- bdrkreg_t i_e_prb_e : 1;
- bdrkreg_t i_e_prb_f : 1;
- bdrkreg_t i_e_crazy : 1;
- bdrkreg_t i_e_bte_0 : 1;
- bdrkreg_t i_e_bte_1 : 1;
- bdrkreg_t i_reserved_1 : 9;
- bdrkreg_t i_ii_internal : 1;
- bdrkreg_t i_spur_rd_hdr : 1;
- bdrkreg_t i_pi0_forward_int : 1;
- bdrkreg_t i_pi1_forward_int : 1;
- bdrkreg_t i_reserved : 32;
- } ii_ieclr_fld_s;
-} ii_ieclr_u_t;
-
-#else
-
-typedef union ii_ieclr_u {
- bdrkreg_t ii_ieclr_regval;
- struct {
- bdrkreg_t i_reserved : 32;
- bdrkreg_t i_pi1_forward_int : 1;
- bdrkreg_t i_pi0_forward_int : 1;
- bdrkreg_t i_spur_rd_hdr : 1;
- bdrkreg_t i_ii_internal : 1;
- bdrkreg_t i_reserved_1 : 9;
- bdrkreg_t i_e_bte_1 : 1;
- bdrkreg_t i_e_bte_0 : 1;
- bdrkreg_t i_e_crazy : 1;
- bdrkreg_t i_e_prb_f : 1;
- bdrkreg_t i_e_prb_e : 1;
- bdrkreg_t i_e_prb_d : 1;
- bdrkreg_t i_e_prb_c : 1;
- bdrkreg_t i_e_prb_b : 1;
- bdrkreg_t i_e_prb_a : 1;
- bdrkreg_t i_e_prb_9 : 1;
- bdrkreg_t i_e_prb_8 : 1;
- bdrkreg_t i_rsvd : 7;
- bdrkreg_t i_e_prb_0 : 1;
- } ii_ieclr_fld_s;
-} ii_ieclr_u_t;
-
-#endif
-
-
-
-
-
-/************************************************************************
- * *
- * This register controls both BTEs. SOFT_RESET is intended for *
- * recovery after an error. COUNT controls the total number of CRBs *
- * that both BTEs (combined) can use, which affects total BTE *
- * bandwidth. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibcr_u {
- bdrkreg_t ii_ibcr_regval;
- struct {
- bdrkreg_t i_count : 4;
- bdrkreg_t i_rsvd_1 : 4;
- bdrkreg_t i_soft_reset : 1;
- bdrkreg_t i_rsvd : 55;
- } ii_ibcr_fld_s;
-} ii_ibcr_u_t;
-
-#else
-
-typedef union ii_ibcr_u {
- bdrkreg_t ii_ibcr_regval;
- struct {
- bdrkreg_t i_rsvd : 55;
- bdrkreg_t i_soft_reset : 1;
- bdrkreg_t i_rsvd_1 : 4;
- bdrkreg_t i_count : 4;
- } ii_ibcr_fld_s;
-} ii_ibcr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the header of a spurious read response *
- * received from Crosstalk. A spurious read response is defined as a *
- * read response received by II from a widget for which (1) the SIDN *
- * has a value between 1 and 7, inclusive (II never sends requests to *
- * these widgets (2) there is no valid IPRTE register which *
- * corresponds to the TNUM, or (3) the widget indicated in SIDN is *
- * not the same as the widget recorded in the IPRTE register *
- * referenced by the TNUM. If this condition is true, and if the *
- * IXSS[VALID] bit is clear, then the header of the spurious read *
- * response is capture in IXSM and IXSS, and IXSS[VALID] is set. The *
- * errant header is thereby captured, and no further spurious read *
- * respones are captured until IXSS[VALID] is cleared by setting the *
- * appropriate bit in IECLR.Everytime a spurious read response is *
- * detected, the SPUR_RD bit of the PRB corresponding to the incoming *
- * message's SIDN field is set. This always happens, regarless of *
- * whether a header is captured. The programmer should check *
- * IXSM[SIDN] to determine which widget sent the spurious response, *
- * because there may be more than one SPUR_RD bit set in the PRB *
- * registers. The widget indicated by IXSM[SIDN] was the first *
- * spurious read response to be received since the last time *
- * IXSS[VALID] was clear. The SPUR_RD bit of the corresponding PRB *
- * will be set. Any SPUR_RD bits in any other PRB registers indicate *
- * spurious messages from other widets which were detected after the *
- * header was captured.. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ixsm_u {
- bdrkreg_t ii_ixsm_regval;
- struct {
- bdrkreg_t i_byte_en : 32;
- bdrkreg_t i_reserved : 1;
- bdrkreg_t i_tag : 3;
- bdrkreg_t i_alt_pactyp : 4;
- bdrkreg_t i_bo : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_vbpm : 1;
- bdrkreg_t i_gbr : 1;
- bdrkreg_t i_ds : 2;
- bdrkreg_t i_ct : 1;
- bdrkreg_t i_tnum : 5;
- bdrkreg_t i_pactyp : 4;
- bdrkreg_t i_sidn : 4;
- bdrkreg_t i_didn : 4;
- } ii_ixsm_fld_s;
-} ii_ixsm_u_t;
-
-#else
-
-typedef union ii_ixsm_u {
- bdrkreg_t ii_ixsm_regval;
- struct {
- bdrkreg_t i_didn : 4;
- bdrkreg_t i_sidn : 4;
- bdrkreg_t i_pactyp : 4;
- bdrkreg_t i_tnum : 5;
- bdrkreg_t i_ct : 1;
- bdrkreg_t i_ds : 2;
- bdrkreg_t i_gbr : 1;
- bdrkreg_t i_vbpm : 1;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_bo : 1;
- bdrkreg_t i_alt_pactyp : 4;
- bdrkreg_t i_tag : 3;
- bdrkreg_t i_reserved : 1;
- bdrkreg_t i_byte_en : 32;
- } ii_ixsm_fld_s;
-} ii_ixsm_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the sideband bits of a spurious read *
- * response received from Crosstalk. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ixss_u {
- bdrkreg_t ii_ixss_regval;
- struct {
- bdrkreg_t i_sideband : 8;
- bdrkreg_t i_rsvd : 55;
- bdrkreg_t i_valid : 1;
- } ii_ixss_fld_s;
-} ii_ixss_u_t;
-
-#else
-
-typedef union ii_ixss_u {
- bdrkreg_t ii_ixss_regval;
- struct {
- bdrkreg_t i_valid : 1;
- bdrkreg_t i_rsvd : 55;
- bdrkreg_t i_sideband : 8;
- } ii_ixss_fld_s;
-} ii_ixss_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register enables software to access the II LLP's test port. *
- * Refer to the LLP 2.5 documentation for an explanation of the test *
- * port. Software can write to this register to program the values *
- * for the control fields (TestErrCapture, TestClear, TestFlit, *
- * TestMask and TestSeed). Similarly, software can read from this *
- * register to obtain the values of the test port's status outputs *
- * (TestCBerr, TestValid and TestData). *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ilct_u {
- bdrkreg_t ii_ilct_regval;
- struct {
- bdrkreg_t i_test_seed : 20;
- bdrkreg_t i_test_mask : 8;
- bdrkreg_t i_test_data : 20;
- bdrkreg_t i_test_valid : 1;
- bdrkreg_t i_test_cberr : 1;
- bdrkreg_t i_test_flit : 3;
- bdrkreg_t i_test_clear : 1;
- bdrkreg_t i_test_err_capture : 1;
- bdrkreg_t i_rsvd : 9;
- } ii_ilct_fld_s;
-} ii_ilct_u_t;
-
-#else
-
-typedef union ii_ilct_u {
- bdrkreg_t ii_ilct_regval;
- struct {
- bdrkreg_t i_rsvd : 9;
- bdrkreg_t i_test_err_capture : 1;
- bdrkreg_t i_test_clear : 1;
- bdrkreg_t i_test_flit : 3;
- bdrkreg_t i_test_cberr : 1;
- bdrkreg_t i_test_valid : 1;
- bdrkreg_t i_test_data : 20;
- bdrkreg_t i_test_mask : 8;
- bdrkreg_t i_test_seed : 20;
- } ii_ilct_fld_s;
-} ii_ilct_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * If the II detects an illegal incoming Duplonet packet (request or *
- * reply) when VALID==0 in the IIEPH1 register, then it saves the *
- * contents of the packet's header flit in the IIEPH1 and IIEPH2 *
- * registers, sets the VALID bit in IIEPH1, clears the OVERRUN bit, *
- * and assigns a value to the ERR_TYPE field which indicates the *
- * specific nature of the error. The II recognizes four different *
- * types of errors: short request packets (ERR_TYPE==2), short reply *
- * packets (ERR_TYPE==3), long request packets (ERR_TYPE==4) and long *
- * reply packets (ERR_TYPE==5). The encodings for these types of *
- * errors were chosen to be consistent with the same types of errors *
- * indicated by the ERR_TYPE field in the LB_ERROR_HDR1 register (in *
- * the LB unit). If the II detects an illegal incoming Duplonet *
- * packet when VALID==1 in the IIEPH1 register, then it merely sets *
- * the OVERRUN bit to indicate that a subsequent error has happened, *
- * and does nothing further. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iieph1_u {
- bdrkreg_t ii_iieph1_regval;
- struct {
- bdrkreg_t i_command : 7;
- bdrkreg_t i_rsvd_5 : 1;
- bdrkreg_t i_suppl : 11;
- bdrkreg_t i_rsvd_4 : 1;
- bdrkreg_t i_source : 11;
- bdrkreg_t i_rsvd_3 : 1;
- bdrkreg_t i_err_type : 4;
- bdrkreg_t i_rsvd_2 : 4;
- bdrkreg_t i_overrun : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_valid : 1;
- bdrkreg_t i_rsvd : 19;
- } ii_iieph1_fld_s;
-} ii_iieph1_u_t;
-
-#else
-
-typedef union ii_iieph1_u {
- bdrkreg_t ii_iieph1_regval;
- struct {
- bdrkreg_t i_rsvd : 19;
- bdrkreg_t i_valid : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_overrun : 1;
- bdrkreg_t i_rsvd_2 : 4;
- bdrkreg_t i_err_type : 4;
- bdrkreg_t i_rsvd_3 : 1;
- bdrkreg_t i_source : 11;
- bdrkreg_t i_rsvd_4 : 1;
- bdrkreg_t i_suppl : 11;
- bdrkreg_t i_rsvd_5 : 1;
- bdrkreg_t i_command : 7;
- } ii_iieph1_fld_s;
-} ii_iieph1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register holds the Address field from the header flit of an *
- * incoming erroneous Duplonet packet, along with the tail bit which *
- * accompanied this header flit. This register is essentially an *
- * extension of IIEPH1. Two registers were necessary because the 64 *
- * bits available in only a single register were insufficient to *
- * capture the entire header flit of an erroneous packet. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iieph2_u {
- bdrkreg_t ii_iieph2_regval;
- struct {
- bdrkreg_t i_address : 38;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_tail : 1;
- bdrkreg_t i_rsvd : 23;
- } ii_iieph2_fld_s;
-} ii_iieph2_u_t;
-
-#else
-
-typedef union ii_iieph2_u {
- bdrkreg_t ii_iieph2_regval;
- struct {
- bdrkreg_t i_rsvd : 23;
- bdrkreg_t i_tail : 1;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_address : 38;
- } ii_iieph2_fld_s;
-} ii_iieph2_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * A write to this register causes a particular field in the *
- * corresponding widget's PRB entry to be adjusted up or down by 1. *
- * This counter should be used when recovering from error and reset *
- * conditions. Note that software would be capable of causing *
- * inadvertent overflow or underflow of these counters. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ipca_u {
- bdrkreg_t ii_ipca_regval;
- struct {
- bdrkreg_t i_wid : 4;
- bdrkreg_t i_adjust : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_field : 2;
- bdrkreg_t i_rsvd : 54;
- } ii_ipca_fld_s;
-} ii_ipca_u_t;
-
-#else
-
-typedef union ii_ipca_u {
- bdrkreg_t ii_ipca_regval;
- struct {
- bdrkreg_t i_rsvd : 54;
- bdrkreg_t i_field : 2;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_adjust : 1;
- bdrkreg_t i_wid : 4;
- } ii_ipca_fld_s;
-} ii_ipca_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte0_u {
- bdrkreg_t ii_iprte0_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte0_fld_s;
-} ii_iprte0_u_t;
-
-#else
-
-typedef union ii_iprte0_u {
- bdrkreg_t ii_iprte0_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte0_fld_s;
-} ii_iprte0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte1_u {
- bdrkreg_t ii_iprte1_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte1_fld_s;
-} ii_iprte1_u_t;
-
-#else
-
-typedef union ii_iprte1_u {
- bdrkreg_t ii_iprte1_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte1_fld_s;
-} ii_iprte1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte2_u {
- bdrkreg_t ii_iprte2_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte2_fld_s;
-} ii_iprte2_u_t;
-
-#else
-
-typedef union ii_iprte2_u {
- bdrkreg_t ii_iprte2_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte2_fld_s;
-} ii_iprte2_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte3_u {
- bdrkreg_t ii_iprte3_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte3_fld_s;
-} ii_iprte3_u_t;
-
-#else
-
-typedef union ii_iprte3_u {
- bdrkreg_t ii_iprte3_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte3_fld_s;
-} ii_iprte3_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte4_u {
- bdrkreg_t ii_iprte4_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte4_fld_s;
-} ii_iprte4_u_t;
-
-#else
-
-typedef union ii_iprte4_u {
- bdrkreg_t ii_iprte4_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte4_fld_s;
-} ii_iprte4_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte5_u {
- bdrkreg_t ii_iprte5_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte5_fld_s;
-} ii_iprte5_u_t;
-
-#else
-
-typedef union ii_iprte5_u {
- bdrkreg_t ii_iprte5_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte5_fld_s;
-} ii_iprte5_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte6_u {
- bdrkreg_t ii_iprte6_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte6_fld_s;
-} ii_iprte6_u_t;
-
-#else
-
-typedef union ii_iprte6_u {
- bdrkreg_t ii_iprte6_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte6_fld_s;
-} ii_iprte6_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * There are 8 instances of this register. This register contains *
- * the information that the II has to remember once it has launched a *
- * PIO Read operation. The contents are used to form the correct *
- * Router Network packet and direct the Crosstalk reply to the *
- * appropriate processor. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iprte7_u {
- bdrkreg_t ii_iprte7_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_vld : 1;
- } ii_iprte7_fld_s;
-} ii_iprte7_u_t;
-
-#else
-
-typedef union ii_iprte7_u {
- bdrkreg_t ii_iprte7_regval;
- struct {
- bdrkreg_t i_vld : 1;
- bdrkreg_t i_to_cnt : 5;
- bdrkreg_t i_widget : 4;
- bdrkreg_t i_rsvd : 2;
- bdrkreg_t i_source : 8;
- bdrkreg_t i_init : 3;
- bdrkreg_t i_addr : 38;
- bdrkreg_t i_rsvd_1 : 3;
- } ii_iprte7_fld_s;
-} ii_iprte7_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: Bedrock_II contains a feature which did not exist in *
- * the Hub which automatically cleans up after a Read Response *
- * timeout, including deallocation of the IPRTE and recovery of IBuf *
- * space. The inclusion of this register in Bedrock is for backward *
- * compatibility *
- * A write to this register causes an entry from the table of *
- * outstanding PIO Read Requests to be freed and returned to the *
- * stack of free entries. This register is used in handling the *
- * timeout errors that result in a PIO Reply never returning from *
- * Crosstalk. *
- * Note that this register does not affect the contents of the IPRTE *
- * registers. The Valid bits in those registers have to be *
- * specifically turned off by software. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ipdr_u {
- bdrkreg_t ii_ipdr_regval;
- struct {
- bdrkreg_t i_te : 3;
- bdrkreg_t i_rsvd_1 : 1;
- bdrkreg_t i_pnd : 1;
- bdrkreg_t i_init_rpcnt : 1;
- bdrkreg_t i_rsvd : 58;
- } ii_ipdr_fld_s;
-} ii_ipdr_u_t;
-
-#else
-
-typedef union ii_ipdr_u {
- bdrkreg_t ii_ipdr_regval;
- struct {
- bdrkreg_t i_rsvd : 58;
- bdrkreg_t i_init_rpcnt : 1;
- bdrkreg_t i_pnd : 1;
- bdrkreg_t i_rsvd_1 : 1;
- bdrkreg_t i_te : 3;
- } ii_ipdr_fld_s;
-} ii_ipdr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * A write to this register causes a CRB entry to be returned to the *
- * queue of free CRBs. The entry should have previously been cleared *
- * (mark bit) via backdoor access to the pertinent CRB entry. This *
- * register is used in the last step of handling the errors that are *
- * captured and marked in CRB entries. Briefly: 1) first error for *
- * DMA write from a particular device, and first error for a *
- * particular BTE stream, lead to a marked CRB entry, and processor *
- * interrupt, 2) software reads the error information captured in the *
- * CRB entry, and presumably takes some corrective action, 3) *
- * software clears the mark bit, and finally 4) software writes to *
- * the ICDR register to return the CRB entry to the list of free CRB *
- * entries. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icdr_u {
- bdrkreg_t ii_icdr_regval;
- struct {
- bdrkreg_t i_crb_num : 4;
- bdrkreg_t i_pnd : 1;
- bdrkreg_t i_rsvd : 59;
- } ii_icdr_fld_s;
-} ii_icdr_u_t;
-
-#else
-
-typedef union ii_icdr_u {
- bdrkreg_t ii_icdr_regval;
- struct {
- bdrkreg_t i_rsvd : 59;
- bdrkreg_t i_pnd : 1;
- bdrkreg_t i_crb_num : 4;
- } ii_icdr_fld_s;
-} ii_icdr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register provides debug access to two FIFOs inside of II. *
- * Both IOQ_MAX* fields of this register contain the instantaneous *
- * depth (in units of the number of available entries) of the *
- * associated IOQ FIFO. A read of this register will return the *
- * number of free entries on each FIFO at the time of the read. So *
- * when a FIFO is idle, the associated field contains the maximum *
- * depth of the FIFO. This register is writable for debug reasons *
- * and is intended to be written with the maximum desired FIFO depth *
- * while the FIFO is idle. Software must assure that II is idle when *
- * this register is written. If there are any active entries in any *
- * of these FIFOs when this register is written, the results are *
- * undefined. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ifdr_u {
- bdrkreg_t ii_ifdr_regval;
- struct {
- bdrkreg_t i_ioq_max_rq : 7;
- bdrkreg_t i_set_ioq_rq : 1;
- bdrkreg_t i_ioq_max_rp : 7;
- bdrkreg_t i_set_ioq_rp : 1;
- bdrkreg_t i_rsvd : 48;
- } ii_ifdr_fld_s;
-} ii_ifdr_u_t;
-
-#else
-
-typedef union ii_ifdr_u {
- bdrkreg_t ii_ifdr_regval;
- struct {
- bdrkreg_t i_rsvd : 48;
- bdrkreg_t i_set_ioq_rp : 1;
- bdrkreg_t i_ioq_max_rp : 7;
- bdrkreg_t i_set_ioq_rq : 1;
- bdrkreg_t i_ioq_max_rq : 7;
- } ii_ifdr_fld_s;
-} ii_ifdr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register allows the II to become sluggish in removing *
- * messages from its inbound queue (IIQ). This will cause messages to *
- * back up in either virtual channel. Disabling the "molasses" mode *
- * subsequently allows the II to be tested under stress. In the *
- * sluggish ("Molasses") mode, the localized effects of congestion *
- * can be observed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iiap_u {
- bdrkreg_t ii_iiap_regval;
- struct {
- bdrkreg_t i_rq_mls : 6;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_rp_mls : 6;
- bdrkreg_t i_rsvd : 50;
- } ii_iiap_fld_s;
-} ii_iiap_u_t;
-
-#else
-
-typedef union ii_iiap_u {
- bdrkreg_t ii_iiap_regval;
- struct {
- bdrkreg_t i_rsvd : 50;
- bdrkreg_t i_rp_mls : 6;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_rq_mls : 6;
- } ii_iiap_fld_s;
-} ii_iiap_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register allows several parameters of CRB operation to be *
- * set. Note that writing to this register can have catastrophic side *
- * effects, if the CRB is not quiescent, i.e. if the CRB is *
- * processing protocol messages when the write occurs. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icmr_u {
- bdrkreg_t ii_icmr_regval;
- struct {
- bdrkreg_t i_sp_msg : 1;
- bdrkreg_t i_rd_hdr : 1;
- bdrkreg_t i_rsvd_4 : 2;
- bdrkreg_t i_c_cnt : 4;
- bdrkreg_t i_rsvd_3 : 4;
- bdrkreg_t i_clr_rqpd : 1;
- bdrkreg_t i_clr_rppd : 1;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_fc_cnt : 4;
- bdrkreg_t i_crb_vld : 15;
- bdrkreg_t i_crb_mark : 15;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_precise : 1;
- bdrkreg_t i_rsvd : 11;
- } ii_icmr_fld_s;
-} ii_icmr_u_t;
-
-#else
-
-typedef union ii_icmr_u {
- bdrkreg_t ii_icmr_regval;
- struct {
- bdrkreg_t i_rsvd : 11;
- bdrkreg_t i_precise : 1;
- bdrkreg_t i_rsvd_1 : 2;
- bdrkreg_t i_crb_mark : 15;
- bdrkreg_t i_crb_vld : 15;
- bdrkreg_t i_fc_cnt : 4;
- bdrkreg_t i_rsvd_2 : 2;
- bdrkreg_t i_clr_rppd : 1;
- bdrkreg_t i_clr_rqpd : 1;
- bdrkreg_t i_rsvd_3 : 4;
- bdrkreg_t i_c_cnt : 4;
- bdrkreg_t i_rsvd_4 : 2;
- bdrkreg_t i_rd_hdr : 1;
- bdrkreg_t i_sp_msg : 1;
- } ii_icmr_fld_s;
-} ii_icmr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register allows control of the table portion of the CRB *
- * logic via software. Control operations from this register have *
- * priority over all incoming Crosstalk or BTE requests. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_iccr_u {
- bdrkreg_t ii_iccr_regval;
- struct {
- bdrkreg_t i_crb_num : 4;
- bdrkreg_t i_rsvd_1 : 4;
- bdrkreg_t i_cmd : 8;
- bdrkreg_t i_pending : 1;
- bdrkreg_t i_rsvd : 47;
- } ii_iccr_fld_s;
-} ii_iccr_u_t;
-
-#else
-
-typedef union ii_iccr_u {
- bdrkreg_t ii_iccr_regval;
- struct {
- bdrkreg_t i_rsvd : 47;
- bdrkreg_t i_pending : 1;
- bdrkreg_t i_cmd : 8;
- bdrkreg_t i_rsvd_1 : 4;
- bdrkreg_t i_crb_num : 4;
- } ii_iccr_fld_s;
-} ii_iccr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register allows the maximum timeout value to be programmed. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icto_u {
- bdrkreg_t ii_icto_regval;
- struct {
- bdrkreg_t i_timeout : 8;
- bdrkreg_t i_rsvd : 56;
- } ii_icto_fld_s;
-} ii_icto_u_t;
-
-#else
-
-typedef union ii_icto_u {
- bdrkreg_t ii_icto_regval;
- struct {
- bdrkreg_t i_rsvd : 56;
- bdrkreg_t i_timeout : 8;
- } ii_icto_fld_s;
-} ii_icto_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register allows the timeout prescalar to be programmed. An *
- * internal counter is associated with this register. When the *
- * internal counter reaches the value of the PRESCALE field, the *
- * timer registers in all valid CRBs are incremented (CRBx_D[TIMEOUT] *
- * field). The internal counter resets to zero, and then continues *
- * counting. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ictp_u {
- bdrkreg_t ii_ictp_regval;
- struct {
- bdrkreg_t i_prescale : 24;
- bdrkreg_t i_rsvd : 40;
- } ii_ictp_fld_s;
-} ii_ictp_u_t;
-
-#else
-
-typedef union ii_ictp_u {
- bdrkreg_t ii_ictp_regval;
- struct {
- bdrkreg_t i_rsvd : 40;
- bdrkreg_t i_prescale : 24;
- } ii_ictp_fld_s;
-} ii_ictp_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 15 CRB Entries (ICRB0 to ICRBE) that are *
- * used for Crosstalk operations (both cacheline and partial *
- * operations) or BTE/IO. Because the CRB entries are very wide, four *
- * registers (_A to _D) are required to read and write each entry. *
- * The CRB Entry registers can be conceptualized as rows and columns *
- * (illustrated in the table above). Each row contains the 4 *
- * registers required for a single CRB Entry. The first doubleword *
- * (column) for each entry is labeled A, and the second doubleword *
- * (higher address) is labeled B, the third doubleword is labeled C, *
- * and the fourth doubleword is labeled D. All CRB entries have their *
- * addresses on a quarter cacheline aligned boundary. *
- * Upon reset, only the following fields are initialized: valid *
- * (VLD), priority count, timeout, timeout valid, and context valid. *
- * All other bits should be cleared by software before use (after *
- * recovering any potential error state from before the reset). *
- * The following four tables summarize the format for the four *
- * registers that are used for each ICRB# Entry. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icrb0_a_u {
- bdrkreg_t ii_icrb0_a_regval;
- struct {
- bdrkreg_t ia_iow : 1;
- bdrkreg_t ia_vld : 1;
- bdrkreg_t ia_addr : 38;
- bdrkreg_t ia_tnum : 5;
- bdrkreg_t ia_sidn : 4;
- bdrkreg_t ia_xt_err : 1;
- bdrkreg_t ia_mark : 1;
- bdrkreg_t ia_ln_uce : 1;
- bdrkreg_t ia_errcode : 3;
- bdrkreg_t ia_error : 1;
- bdrkreg_t ia_stall__bte_1 : 1;
- bdrkreg_t ia_stall__bte_0 : 1;
- bdrkreg_t ia_rsvd : 6;
- } ii_icrb0_a_fld_s;
-} ii_icrb0_a_u_t;
-
-#else
-
-typedef union ii_icrb0_a_u {
- bdrkreg_t ii_icrb0_a_regval;
- struct {
- bdrkreg_t ia_rsvd : 6;
- bdrkreg_t ia_stall__bte_0 : 1;
- bdrkreg_t ia_stall__bte_1 : 1;
- bdrkreg_t ia_error : 1;
- bdrkreg_t ia_errcode : 3;
- bdrkreg_t ia_ln_uce : 1;
- bdrkreg_t ia_mark : 1;
- bdrkreg_t ia_xt_err : 1;
- bdrkreg_t ia_sidn : 4;
- bdrkreg_t ia_tnum : 5;
- bdrkreg_t ia_addr : 38;
- bdrkreg_t ia_vld : 1;
- bdrkreg_t ia_iow : 1;
- } ii_icrb0_a_fld_s;
-} ii_icrb0_a_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 15 CRB Entries (ICRB0 to ICRBE) that are *
- * used for Crosstalk operations (both cacheline and partial *
- * operations) or BTE/IO. Because the CRB entries are very wide, four *
- * registers (_A to _D) are required to read and write each entry. *
- * *
- ************************************************************************/
-
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icrb0_b_u {
- bdrkreg_t ii_icrb0_b_regval;
- struct {
- bdrkreg_t ib_stall__intr : 1;
- bdrkreg_t ib_stall_ib : 1;
- bdrkreg_t ib_intvn : 1;
- bdrkreg_t ib_wb : 1;
- bdrkreg_t ib_hold : 1;
- bdrkreg_t ib_ack : 1;
- bdrkreg_t ib_resp : 1;
- bdrkreg_t ib_ack_cnt : 11;
- bdrkreg_t ib_rsvd_1 : 7;
- bdrkreg_t ib_exc : 5;
- bdrkreg_t ib_init : 3;
- bdrkreg_t ib_imsg : 8;
- bdrkreg_t ib_imsgtype : 2;
- bdrkreg_t ib_use_old : 1;
- bdrkreg_t ib_source : 12;
- bdrkreg_t ib_size : 2;
- bdrkreg_t ib_ct : 1;
- bdrkreg_t ib_bte_num : 1;
- bdrkreg_t ib_rsvd : 4;
- } ii_icrb0_b_fld_s;
-} ii_icrb0_b_u_t;
-
-#else
-
-typedef union ii_icrb0_b_u {
- bdrkreg_t ii_icrb0_b_regval;
- struct {
- bdrkreg_t ib_rsvd : 4;
- bdrkreg_t ib_bte_num : 1;
- bdrkreg_t ib_ct : 1;
- bdrkreg_t ib_size : 2;
- bdrkreg_t ib_source : 12;
- bdrkreg_t ib_use_old : 1;
- bdrkreg_t ib_imsgtype : 2;
- bdrkreg_t ib_imsg : 8;
- bdrkreg_t ib_init : 3;
- bdrkreg_t ib_exc : 5;
- bdrkreg_t ib_rsvd_1 : 7;
- bdrkreg_t ib_ack_cnt : 11;
- bdrkreg_t ib_resp : 1;
- bdrkreg_t ib_ack : 1;
- bdrkreg_t ib_hold : 1;
- bdrkreg_t ib_wb : 1;
- bdrkreg_t ib_intvn : 1;
- bdrkreg_t ib_stall_ib : 1;
- bdrkreg_t ib_stall__intr : 1;
- } ii_icrb0_b_fld_s;
-} ii_icrb0_b_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: There are 15 CRB Entries (ICRB0 to ICRBE) that are *
- * used for Crosstalk operations (both cacheline and partial *
- * operations) or BTE/IO. Because the CRB entries are very wide, four *
- * registers (_A to _D) are required to read and write each entry. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icrb0_c_u {
- bdrkreg_t ii_icrb0_c_regval;
- struct {
- bdrkreg_t ic_gbr : 1;
- bdrkreg_t ic_resprqd : 1;
- bdrkreg_t ic_bo : 1;
- bdrkreg_t ic_suppl : 12;
- bdrkreg_t ic_pa_be : 34;
- bdrkreg_t ic_bte_op : 1;
- bdrkreg_t ic_pr_psc : 4;
- bdrkreg_t ic_pr_cnt : 4;
- bdrkreg_t ic_sleep : 1;
- bdrkreg_t ic_rsvd : 5;
- } ii_icrb0_c_fld_s;
-} ii_icrb0_c_u_t;
-
-#else
-
-typedef union ii_icrb0_c_u {
- bdrkreg_t ii_icrb0_c_regval;
- struct {
- bdrkreg_t ic_rsvd : 5;
- bdrkreg_t ic_sleep : 1;
- bdrkreg_t ic_pr_cnt : 4;
- bdrkreg_t ic_pr_psc : 4;
- bdrkreg_t ic_bte_op : 1;
- bdrkreg_t ic_pa_be : 34;
- bdrkreg_t ic_suppl : 12;
- bdrkreg_t ic_bo : 1;
- bdrkreg_t ic_resprqd : 1;
- bdrkreg_t ic_gbr : 1;
- } ii_icrb0_c_fld_s;
-} ii_icrb0_c_u_t;
-
-#endif
-
-
-
-/************************************************************************
- * *
- * Description: There are 15 CRB Entries (ICRB0 to ICRBE) that are *
- * used for Crosstalk operations (both cacheline and partial *
- * operations) or BTE/IO. Because the CRB entries are very wide, four *
- * registers (_A to _D) are required to read and write each entry. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icrb0_d_u {
- bdrkreg_t ii_icrb0_d_regval;
- struct {
- bdrkreg_t id_timeout : 8;
- bdrkreg_t id_context : 15;
- bdrkreg_t id_rsvd_1 : 1;
- bdrkreg_t id_tvld : 1;
- bdrkreg_t id_cvld : 1;
- bdrkreg_t id_rsvd : 38;
- } ii_icrb0_d_fld_s;
-} ii_icrb0_d_u_t;
-
-#else
-
-typedef union ii_icrb0_d_u {
- bdrkreg_t ii_icrb0_d_regval;
- struct {
- bdrkreg_t id_rsvd : 38;
- bdrkreg_t id_cvld : 1;
- bdrkreg_t id_tvld : 1;
- bdrkreg_t id_rsvd_1 : 1;
- bdrkreg_t id_context : 15;
- bdrkreg_t id_timeout : 8;
- } ii_icrb0_d_fld_s;
-} ii_icrb0_d_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the lower 64 bits of the header of the *
- * spurious message captured by II. Valid when the SP_MSG bit in ICMR *
- * register is set. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icsml_u {
- bdrkreg_t ii_icsml_regval;
- struct {
- bdrkreg_t i_tt_addr : 38;
- bdrkreg_t i_tt_ack_cnt : 11;
- bdrkreg_t i_newsuppl_ex : 11;
- bdrkreg_t i_reserved : 3;
- bdrkreg_t i_overflow : 1;
- } ii_icsml_fld_s;
-} ii_icsml_u_t;
-
-#else
-
-typedef union ii_icsml_u {
- bdrkreg_t ii_icsml_regval;
- struct {
- bdrkreg_t i_overflow : 1;
- bdrkreg_t i_reserved : 3;
- bdrkreg_t i_newsuppl_ex : 11;
- bdrkreg_t i_tt_ack_cnt : 11;
- bdrkreg_t i_tt_addr : 38;
- } ii_icsml_fld_s;
-} ii_icsml_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the microscopic state, all the inputs to *
- * the protocol table, captured with the spurious message. Valid when *
- * the SP_MSG bit in the ICMR register is set. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_icsmh_u {
- bdrkreg_t ii_icsmh_regval;
- struct {
- bdrkreg_t i_tt_vld : 1;
- bdrkreg_t i_xerr : 1;
- bdrkreg_t i_ft_cwact_o : 1;
- bdrkreg_t i_ft_wact_o : 1;
- bdrkreg_t i_ft_active_o : 1;
- bdrkreg_t i_sync : 1;
- bdrkreg_t i_mnusg : 1;
- bdrkreg_t i_mnusz : 1;
- bdrkreg_t i_plusz : 1;
- bdrkreg_t i_plusg : 1;
- bdrkreg_t i_tt_exc : 5;
- bdrkreg_t i_tt_wb : 1;
- bdrkreg_t i_tt_hold : 1;
- bdrkreg_t i_tt_ack : 1;
- bdrkreg_t i_tt_resp : 1;
- bdrkreg_t i_tt_intvn : 1;
- bdrkreg_t i_g_stall_bte1 : 1;
- bdrkreg_t i_g_stall_bte0 : 1;
- bdrkreg_t i_g_stall_il : 1;
- bdrkreg_t i_g_stall_ib : 1;
- bdrkreg_t i_tt_imsg : 8;
- bdrkreg_t i_tt_imsgtype : 2;
- bdrkreg_t i_tt_use_old : 1;
- bdrkreg_t i_tt_respreqd : 1;
- bdrkreg_t i_tt_bte_num : 1;
- bdrkreg_t i_cbn : 1;
- bdrkreg_t i_match : 1;
- bdrkreg_t i_rpcnt_lt_34 : 1;
- bdrkreg_t i_rpcnt_ge_34 : 1;
- bdrkreg_t i_rpcnt_lt_18 : 1;
- bdrkreg_t i_rpcnt_ge_18 : 1;
- bdrkreg_t i_rpcnt_lt_2 : 1;
- bdrkreg_t i_rpcnt_ge_2 : 1;
- bdrkreg_t i_rqcnt_lt_18 : 1;
- bdrkreg_t i_rqcnt_ge_18 : 1;
- bdrkreg_t i_rqcnt_lt_2 : 1;
- bdrkreg_t i_rqcnt_ge_2 : 1;
- bdrkreg_t i_tt_device : 7;
- bdrkreg_t i_tt_init : 3;
- bdrkreg_t i_reserved : 5;
- } ii_icsmh_fld_s;
-} ii_icsmh_u_t;
-
-#else
-
-typedef union ii_icsmh_u {
- bdrkreg_t ii_icsmh_regval;
- struct {
- bdrkreg_t i_reserved : 5;
- bdrkreg_t i_tt_init : 3;
- bdrkreg_t i_tt_device : 7;
- bdrkreg_t i_rqcnt_ge_2 : 1;
- bdrkreg_t i_rqcnt_lt_2 : 1;
- bdrkreg_t i_rqcnt_ge_18 : 1;
- bdrkreg_t i_rqcnt_lt_18 : 1;
- bdrkreg_t i_rpcnt_ge_2 : 1;
- bdrkreg_t i_rpcnt_lt_2 : 1;
- bdrkreg_t i_rpcnt_ge_18 : 1;
- bdrkreg_t i_rpcnt_lt_18 : 1;
- bdrkreg_t i_rpcnt_ge_34 : 1;
- bdrkreg_t i_rpcnt_lt_34 : 1;
- bdrkreg_t i_match : 1;
- bdrkreg_t i_cbn : 1;
- bdrkreg_t i_tt_bte_num : 1;
- bdrkreg_t i_tt_respreqd : 1;
- bdrkreg_t i_tt_use_old : 1;
- bdrkreg_t i_tt_imsgtype : 2;
- bdrkreg_t i_tt_imsg : 8;
- bdrkreg_t i_g_stall_ib : 1;
- bdrkreg_t i_g_stall_il : 1;
- bdrkreg_t i_g_stall_bte0 : 1;
- bdrkreg_t i_g_stall_bte1 : 1;
- bdrkreg_t i_tt_intvn : 1;
- bdrkreg_t i_tt_resp : 1;
- bdrkreg_t i_tt_ack : 1;
- bdrkreg_t i_tt_hold : 1;
- bdrkreg_t i_tt_wb : 1;
- bdrkreg_t i_tt_exc : 5;
- bdrkreg_t i_plusg : 1;
- bdrkreg_t i_plusz : 1;
- bdrkreg_t i_mnusz : 1;
- bdrkreg_t i_mnusg : 1;
- bdrkreg_t i_sync : 1;
- bdrkreg_t i_ft_active_o : 1;
- bdrkreg_t i_ft_wact_o : 1;
- bdrkreg_t i_ft_cwact_o : 1;
- bdrkreg_t i_xerr : 1;
- bdrkreg_t i_tt_vld : 1;
- } ii_icsmh_fld_s;
-} ii_icsmh_u_t;
-
-#endif
-
-
-/************************************************************************
- * *
- * The Bedrock DEBUG unit provides a 3-bit selection signal to the *
- * II unit, thus allowing a choice of one set of debug signal outputs *
- * from a menu of 8 options. Each option is limited to 32 bits in *
- * size. There are more signals of interest than can be accommodated *
- * in this 8*32 framework, so the IDBSS register has been defined to *
- * extend the range of choices available. For each menu option *
- * available to the DEBUG unit, the II provides a "submenu" of *
- * several options. The value of the SUBMENU field in the IDBSS *
- * register selects the desired submenu. Hence, the particular debug *
- * signals provided by the II are determined by the 3-bit selection *
- * signal from the DEBUG unit and the value of the SUBMENU field *
- * within the IDBSS register. For a detailed description of the *
- * available menus and submenus for II debug signals, refer to the *
- * documentation in ii_interface.doc.. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LIITLE_ENDIAN
-
-typedef union ii_idbss_u {
- bdrkreg_t ii_idbss_regval;
- struct {
- bdrkreg_t i_submenu : 3;
- bdrkreg_t i_rsvd : 61;
- } ii_idbss_fld_s;
-} ii_idbss_u_t;
-
-#else
-
-typedef union ii_idbss_u {
- bdrkreg_t ii_idbss_regval;
- struct {
- bdrkreg_t i_rsvd : 61;
- bdrkreg_t i_submenu : 3;
- } ii_idbss_fld_s;
-} ii_idbss_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This register is used to set up the length for a *
- * transfer and then to monitor the progress of that transfer. This *
- * register needs to be initialized before a transfer is started. A *
- * legitimate write to this register will set the Busy bit, clear the *
- * Error bit, and initialize the length to the value desired. *
- * While the transfer is in progress, hardware will decrement the *
- * length field with each successful block that is copied. Once the *
- * transfer completes, hardware will clear the Busy bit. The length *
- * field will also contain the number of cache lines left to be *
- * transferred. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LIITLE_ENDIAN
-
-typedef union ii_ibls0_u {
- bdrkreg_t ii_ibls0_regval;
- struct {
- bdrkreg_t i_length : 16;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_busy : 1;
- bdrkreg_t i_rsvd : 43;
- } ii_ibls0_fld_s;
-} ii_ibls0_u_t;
-
-#else
-
-typedef union ii_ibls0_u {
- bdrkreg_t ii_ibls0_regval;
- struct {
- bdrkreg_t i_rsvd : 43;
- bdrkreg_t i_busy : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_length : 16;
- } ii_ibls0_fld_s;
-} ii_ibls0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register should be loaded before a transfer is started. The *
- * address to be loaded in bits 39:0 is the 40-bit TRex+ physical *
- * address as described in Section 1.3, Figure2 and Figure3. Since *
- * the bottom 7 bits of the address are always taken to be zero, BTE *
- * transfers are always cacheline-aligned. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibsa0_u {
- bdrkreg_t ii_ibsa0_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd : 24;
- } ii_ibsa0_fld_s;
-} ii_ibsa0_u_t;
-
-#else
-
-typedef union ii_ibsa0_u {
- bdrkreg_t ii_ibsa0_regval;
- struct {
- bdrkreg_t i_rsvd : 24;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd_1 : 7;
- } ii_ibsa0_fld_s;
-} ii_ibsa0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register should be loaded before a transfer is started. The *
- * address to be loaded in bits 39:0 is the 40-bit TRex+ physical *
- * address as described in Section 1.3, Figure2 and Figure3. Since *
- * the bottom 7 bits of the address are always taken to be zero, BTE *
- * transfers are always cacheline-aligned. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibda0_u {
- bdrkreg_t ii_ibda0_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd : 24;
- } ii_ibda0_fld_s;
-} ii_ibda0_u_t;
-
-#else
-
-typedef union ii_ibda0_u {
- bdrkreg_t ii_ibda0_regval;
- struct {
- bdrkreg_t i_rsvd : 24;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd_1 : 7;
- } ii_ibda0_fld_s;
-} ii_ibda0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Writing to this register sets up the attributes of the transfer *
- * and initiates the transfer operation. Reading this register has *
- * the side effect of terminating any transfer in progress. Note: *
- * stopping a transfer midstream could have an adverse impact on the *
- * other BTE. If a BTE stream has to be stopped (due to error *
- * handling for example), both BTE streams should be stopped and *
- * their transfers discarded. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibct0_u {
- bdrkreg_t ii_ibct0_regval;
- struct {
- bdrkreg_t i_zerofill : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_notify : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_poison : 1;
- bdrkreg_t i_rsvd : 55;
- } ii_ibct0_fld_s;
-} ii_ibct0_u_t;
-
-#else
-
-typedef union ii_ibct0_u {
- bdrkreg_t ii_ibct0_regval;
- struct {
- bdrkreg_t i_rsvd : 55;
- bdrkreg_t i_poison : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_notify : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_zerofill : 1;
- } ii_ibct0_fld_s;
-} ii_ibct0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the address to which the WINV is sent. *
- * This address has to be cache line aligned. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibna0_u {
- bdrkreg_t ii_ibna0_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd : 24;
- } ii_ibna0_fld_s;
-} ii_ibna0_u_t;
-
-#else
-
-typedef union ii_ibna0_u {
- bdrkreg_t ii_ibna0_regval;
- struct {
- bdrkreg_t i_rsvd : 24;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd_1 : 7;
- } ii_ibna0_fld_s;
-} ii_ibna0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the programmable level as well as the node *
- * ID and PI unit of the processor to which the interrupt will be *
- * sent. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibia0_u {
- bdrkreg_t ii_ibia0_regval;
- struct {
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_node_id : 8;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_level : 7;
- bdrkreg_t i_rsvd : 41;
- } ii_ibia0_fld_s;
-} ii_ibia0_u_t;
-
-#else
-
-typedef union ii_ibia0_u {
- bdrkreg_t ii_ibia0_regval;
- struct {
- bdrkreg_t i_rsvd : 41;
- bdrkreg_t i_level : 7;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_node_id : 8;
- bdrkreg_t i_pi_id : 1;
- } ii_ibia0_fld_s;
-} ii_ibia0_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Description: This register is used to set up the length for a *
- * transfer and then to monitor the progress of that transfer. This *
- * register needs to be initialized before a transfer is started. A *
- * legitimate write to this register will set the Busy bit, clear the *
- * Error bit, and initialize the length to the value desired. *
- * While the transfer is in progress, hardware will decrement the *
- * length field with each successful block that is copied. Once the *
- * transfer completes, hardware will clear the Busy bit. The length *
- * field will also contain the number of cache lines left to be *
- * transferred. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibls1_u {
- bdrkreg_t ii_ibls1_regval;
- struct {
- bdrkreg_t i_length : 16;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_busy : 1;
- bdrkreg_t i_rsvd : 43;
- } ii_ibls1_fld_s;
-} ii_ibls1_u_t;
-
-#else
-
-typedef union ii_ibls1_u {
- bdrkreg_t ii_ibls1_regval;
- struct {
- bdrkreg_t i_rsvd : 43;
- bdrkreg_t i_busy : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_error : 1;
- bdrkreg_t i_length : 16;
- } ii_ibls1_fld_s;
-} ii_ibls1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register should be loaded before a transfer is started. The *
- * address to be loaded in bits 39:0 is the 40-bit TRex+ physical *
- * address as described in Section 1.3, Figure2 and Figure3. Since *
- * the bottom 7 bits of the address are always taken to be zero, BTE *
- * transfers are always cacheline-aligned. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibsa1_u {
- bdrkreg_t ii_ibsa1_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd : 24;
- } ii_ibsa1_fld_s;
-} ii_ibsa1_u_t;
-
-#else
-
-typedef union ii_ibsa1_u {
- bdrkreg_t ii_ibsa1_regval;
- struct {
- bdrkreg_t i_rsvd : 24;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd_1 : 7;
- } ii_ibsa1_fld_s;
-} ii_ibsa1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register should be loaded before a transfer is started. The *
- * address to be loaded in bits 39:0 is the 40-bit TRex+ physical *
- * address as described in Section 1.3, Figure2 and Figure3. Since *
- * the bottom 7 bits of the address are always taken to be zero, BTE *
- * transfers are always cacheline-aligned. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibda1_u {
- bdrkreg_t ii_ibda1_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd : 24;
- } ii_ibda1_fld_s;
-} ii_ibda1_u_t;
-
-#else
-
-typedef union ii_ibda1_u {
- bdrkreg_t ii_ibda1_regval;
- struct {
- bdrkreg_t i_rsvd : 24;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd_1 : 7;
- } ii_ibda1_fld_s;
-} ii_ibda1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * Writing to this register sets up the attributes of the transfer *
- * and initiates the transfer operation. Reading this register has *
- * the side effect of terminating any transfer in progress. Note: *
- * stopping a transfer midstream could have an adverse impact on the *
- * other BTE. If a BTE stream has to be stopped (due to error *
- * handling for example), both BTE streams should be stopped and *
- * their transfers discarded. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibct1_u {
- bdrkreg_t ii_ibct1_regval;
- struct {
- bdrkreg_t i_zerofill : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_notify : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_poison : 1;
- bdrkreg_t i_rsvd : 55;
- } ii_ibct1_fld_s;
-} ii_ibct1_u_t;
-
-#else
-
-typedef union ii_ibct1_u {
- bdrkreg_t ii_ibct1_regval;
- struct {
- bdrkreg_t i_rsvd : 55;
- bdrkreg_t i_poison : 1;
- bdrkreg_t i_rsvd_1 : 3;
- bdrkreg_t i_notify : 1;
- bdrkreg_t i_rsvd_2 : 3;
- bdrkreg_t i_zerofill : 1;
- } ii_ibct1_fld_s;
-} ii_ibct1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the address to which the WINV is sent. *
- * This address has to be cache line aligned. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibna1_u {
- bdrkreg_t ii_ibna1_regval;
- struct {
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd : 24;
- } ii_ibna1_fld_s;
-} ii_ibna1_u_t;
-
-#else
-
-typedef union ii_ibna1_u {
- bdrkreg_t ii_ibna1_regval;
- struct {
- bdrkreg_t i_rsvd : 24;
- bdrkreg_t i_addr : 33;
- bdrkreg_t i_rsvd_1 : 7;
- } ii_ibna1_fld_s;
-} ii_ibna1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register contains the programmable level as well as the node *
- * ID and PI unit of the processor to which the interrupt will be *
- * sent. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ibia1_u {
- bdrkreg_t ii_ibia1_regval;
- struct {
- bdrkreg_t i_pi_id : 1;
- bdrkreg_t i_node_id : 8;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_level : 7;
- bdrkreg_t i_rsvd : 41;
- } ii_ibia1_fld_s;
-} ii_ibia1_u_t;
-
-#else
-
-typedef union ii_ibia1_u {
- bdrkreg_t ii_ibia1_regval;
- struct {
- bdrkreg_t i_rsvd : 41;
- bdrkreg_t i_level : 7;
- bdrkreg_t i_rsvd_1 : 7;
- bdrkreg_t i_node_id : 8;
- bdrkreg_t i_pi_id : 1;
- } ii_ibia1_fld_s;
-} ii_ibia1_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * This register defines the resources that feed information into *
- * the two performance counters located in the IO Performance *
- * Profiling Register. There are 17 different quantities that can be *
- * measured. Given these 17 different options, the two performance *
- * counters have 15 of them in common; menu selections 0 through 0xE *
- * are identical for each performance counter. As for the other two *
- * options, one is available from one performance counter and the *
- * other is available from the other performance counter. Hence, the *
- * II supports all 17*16=272 possible combinations of quantities to *
- * measure. *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ipcr_u {
- bdrkreg_t ii_ipcr_regval;
- struct {
- bdrkreg_t i_ippr0_c : 4;
- bdrkreg_t i_ippr1_c : 4;
- bdrkreg_t i_icct : 8;
- bdrkreg_t i_rsvd : 48;
- } ii_ipcr_fld_s;
-} ii_ipcr_u_t;
-
-#else
-
-typedef union ii_ipcr_u {
- bdrkreg_t ii_ipcr_regval;
- struct {
- bdrkreg_t i_rsvd : 48;
- bdrkreg_t i_icct : 8;
- bdrkreg_t i_ippr1_c : 4;
- bdrkreg_t i_ippr0_c : 4;
- } ii_ipcr_fld_s;
-} ii_ipcr_u_t;
-
-#endif
-
-
-
-
-/************************************************************************
- * *
- * *
- * *
- ************************************************************************/
-
-
-
-
-#ifdef LITTLE_ENDIAN
-
-typedef union ii_ippr_u {
- bdrkreg_t ii_ippr_regval;
- struct {
- bdrkreg_t i_ippr0 : 32;
- bdrkreg_t i_ippr1 : 32;
- } ii_ippr_fld_s;
-} ii_ippr_u_t;
-
-#else
-
-typedef union ii_ippr_u {
- bdrkreg_t ii_ippr_regval;
- struct {
- bdrkreg_t i_ippr1 : 32;
- bdrkreg_t i_ippr0 : 32;
- } ii_ippr_fld_s;
-} ii_ippr_u_t;
-
-#endif
-
-
-
-
-
-
-#endif /* __ASSEMBLY__ */
-
-/************************************************************************
- * *
- * The following defines which were not formed into structures are *
- * probably indentical to another register, and the name of the *
- * register is provided against each of these registers. This *
- * information needs to be checked carefully *
- * *
- * IIO_ICRB1_A IIO_ICRB0_A *
- * IIO_ICRB1_B IIO_ICRB0_B *
- * IIO_ICRB1_C IIO_ICRB0_C *
- * IIO_ICRB1_D IIO_ICRB0_D *
- * IIO_ICRB2_A IIO_ICRB0_A *
- * IIO_ICRB2_B IIO_ICRB0_B *
- * IIO_ICRB2_C IIO_ICRB0_C *
- * IIO_ICRB2_D IIO_ICRB0_D *
- * IIO_ICRB3_A IIO_ICRB0_A *
- * IIO_ICRB3_B IIO_ICRB0_B *
- * IIO_ICRB3_C IIO_ICRB0_C *
- * IIO_ICRB3_D IIO_ICRB0_D *
- * IIO_ICRB4_A IIO_ICRB0_A *
- * IIO_ICRB4_B IIO_ICRB0_B *
- * IIO_ICRB4_C IIO_ICRB0_C *
- * IIO_ICRB4_D IIO_ICRB0_D *
- * IIO_ICRB5_A IIO_ICRB0_A *
- * IIO_ICRB5_B IIO_ICRB0_B *
- * IIO_ICRB5_C IIO_ICRB0_C *
- * IIO_ICRB5_D IIO_ICRB0_D *
- * IIO_ICRB6_A IIO_ICRB0_A *
- * IIO_ICRB6_B IIO_ICRB0_B *
- * IIO_ICRB6_C IIO_ICRB0_C *
- * IIO_ICRB6_D IIO_ICRB0_D *
- * IIO_ICRB7_A IIO_ICRB0_A *
- * IIO_ICRB7_B IIO_ICRB0_B *
- * IIO_ICRB7_C IIO_ICRB0_C *
- * IIO_ICRB7_D IIO_ICRB0_D *
- * IIO_ICRB8_A IIO_ICRB0_A *
- * IIO_ICRB8_B IIO_ICRB0_B *
- * IIO_ICRB8_C IIO_ICRB0_C *
- * IIO_ICRB8_D IIO_ICRB0_D *
- * IIO_ICRB9_A IIO_ICRB0_A *
- * IIO_ICRB9_B IIO_ICRB0_B *
- * IIO_ICRB9_C IIO_ICRB0_C *
- * IIO_ICRB9_D IIO_ICRB0_D *
- * IIO_ICRBA_A IIO_ICRB0_A *
- * IIO_ICRBA_B IIO_ICRB0_B *
- * IIO_ICRBA_C IIO_ICRB0_C *
- * IIO_ICRBA_D IIO_ICRB0_D *
- * IIO_ICRBB_A IIO_ICRB0_A *
- * IIO_ICRBB_B IIO_ICRB0_B *
- * IIO_ICRBB_C IIO_ICRB0_C *
- * IIO_ICRBB_D IIO_ICRB0_D *
- * IIO_ICRBC_A IIO_ICRB0_A *
- * IIO_ICRBC_B IIO_ICRB0_B *
- * IIO_ICRBC_C IIO_ICRB0_C *
- * IIO_ICRBC_D IIO_ICRB0_D *
- * IIO_ICRBD_A IIO_ICRB0_A *
- * IIO_ICRBD_B IIO_ICRB0_B *
- * IIO_ICRBD_C IIO_ICRB0_C *
- * IIO_ICRBD_D IIO_ICRB0_D *
- * IIO_ICRBE_A IIO_ICRB0_A *
- * IIO_ICRBE_B IIO_ICRB0_B *
- * IIO_ICRBE_C IIO_ICRB0_C *
- * IIO_ICRBE_D IIO_ICRB0_D *
- * *
- ************************************************************************/
-
-
-/************************************************************************
- * *
- * MAKE ALL ADDITIONS AFTER THIS LINE *
- * *
- ************************************************************************/
-
-
-
-
-
-#endif /* _ASM_IA64_SN_SN1_HUBIO_H */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)