patch-2.4.25 linux-2.4.25/drivers/i2c/Config.in

• Lines: 50
• Date: 2004-02-18 05:36:31.000000000 -0800
• Orig file: linux-2.4.24/drivers/i2c/Config.in
• Orig date: 2003-08-25 04:44:41.000000000 -0700

diff -urN linux-2.4.24/drivers/i2c/Config.in linux-2.4.25/drivers/i2c/Config.in
@@ -7,20 +7,20 @@
 tristate 'I2C support' CONFIG_I2C
 
 if [ "$CONFIG_I2C" != "n" ]; then
-
    dep_tristate 'I2C bit-banging interfaces'  CONFIG_I2C_ALGOBIT $CONFIG_I2C
    if [ "$CONFIG_I2C_ALGOBIT" != "n" ]; then
       dep_tristate '  Philips style parallel port adapter' CONFIG_I2C_PHILIPSPAR $CONFIG_I2C_ALGOBIT $CONFIG_PARPORT
       dep_tristate '  ELV adapter' CONFIG_I2C_ELV $CONFIG_I2C_ALGOBIT
-      dep_tristate '  Velleman K9000 adapter' CONFIG_I2C_VELLEMAN $CONFIG_I2C_ALGOBIT
+      dep_tristate '  Velleman K8000 adapter' CONFIG_I2C_VELLEMAN $CONFIG_I2C_ALGOBIT
       dep_tristate '  NatSemi SCx200 I2C using GPIO pins' CONFIG_SCx200_I2C $CONFIG_SCx200 $CONFIG_I2C_ALGOBIT
       if [ "$CONFIG_SCx200_I2C" != "n" ]; then
          int  '    GPIO pin used for SCL' CONFIG_SCx200_I2C_SCL 12
          int  '    GPIO pin used for SDA' CONFIG_SCx200_I2C_SDA 13
       fi
-      dep_tristate '  NatSemi SCx200 ACCESS.bus' CONFIG_SCx200_ACB $CONFIG_I2C
    fi
 
+   dep_tristate 'NatSemi SCx200 ACCESS.bus' CONFIG_SCx200_ACB $CONFIG_I2C
+
    dep_tristate 'I2C PCF 8584 interfaces' CONFIG_I2C_ALGOPCF $CONFIG_I2C
    if [ "$CONFIG_I2C_ALGOPCF" != "n" ]; then
       dep_tristate '  Elektor ISA card' CONFIG_I2C_ELEKTOR $CONFIG_I2C_ALGOPCF
@@ -35,7 +35,7 @@
    if [ "$CONFIG_8xx" = "y" ]; then
       dep_tristate 'MPC8xx CPM I2C interface' CONFIG_I2C_ALGO8XX $CONFIG_I2C
       if [ "$CONFIG_RPXLITE" = "y" -o "$CONFIG_RPXCLASSIC" = "y" ]; then
-         dep_tristate '  Embedded Planet RPX Lite/Classic suppoort' CONFIG_I2C_RPXLITE $CONFIG_I2C_ALGO8XX
+         dep_tristate '  Embedded Planet RPX Lite/Classic support' CONFIG_I2C_RPXLITE $CONFIG_I2C_ALGO8XX
       fi
    fi
    if [ "$CONFIG_405" = "y" ]; then
@@ -54,11 +54,14 @@
       dep_tristate '  MAX1617 Temperature Sensor' CONFIG_I2C_MAX1617 $CONFIG_I2C_ALGO_SIBYTE
    fi
 
+   if [ "$CONFIG_SGI_IP22" = "y" ]; then
+      dep_tristate 'I2C SGI interfaces' CONFIG_I2C_ALGO_SGI $CONFIG_I2C
+   fi
+ 
 # This is needed for automatic patch generation: sensors code starts here
 # This is needed for automatic patch generation: sensors code ends here
 
    dep_tristate 'I2C device interface' CONFIG_I2C_CHARDEV $CONFIG_I2C
-   dep_tristate 'I2C /proc interface (required for hardware sensors)' CONFIG_I2C_PROC $CONFIG_I2C
-
+   dep_tristate 'I2C /proc interface (required for hardware sensors)' CONFIG_I2C_PROC $CONFIG_I2C $CONFIG_SYSCTL
 fi
 endmenu